Search:

Type: Posts; User: dslayer

Page 1 of 5 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: batt doors

    by dslayer
    Replies
    5
    Views
    433

    almost all new, i look at them and they seem...

    almost all new, i look at them and they seem good, but a few hard hits and they open, with 7 cells, or with my lipos dont matter, and its not hitting the door,
  2. Replies
    15
    Views
    880

    i use the hitec 645mg servo for single setup,...

    i use the hitec 645mg servo for single setup, more then enough for on track use, now that i did a mmm it seems to be to much steering
  3. Thread: batt doors

    by dslayer
    Replies
    5
    Views
    433

    batt doors

    i have been having problems with the battery doors staying closed, i make sure they are locked in good, but after about 2 laps at the track they always come open, and then the battery will come...
  4. Replies
    9
    Views
    1,903

    opps, i was thinking sc8 not sc10,

    opps, i was thinking sc8 not sc10,
  5. Replies
    9
    Views
    1,903

    body is a little longer, rear wheel wells have to...

    body is a little longer, rear wheel wells have to be opened up a bit to fit, and yes the wheels will work, you just need 17mm adaptors for them
  6. Replies
    13
    Views
    861

    you would set for 2s 2p lipo on the 6v setup,...

    you would set for 2s 2p lipo on the 6v setup, even says it in the manual,lol
  7. Replies
    21
    Views
    941

    consider yourself lucky, i blow them off all the...

    consider yourself lucky, i blow them off all the time on the rear with a stock motor and 7 cell, i had to glue the inside part, then i wouldonly blow the out side, so i removed the rings and ran a...
  8. Thread: Sc10

    by dslayer
    Replies
    15
    Views
    645

    theres pics and a link to it in the slash forum,...

    theres pics and a link to it in the slash forum, and www.teamassociated.com
  9. Thread: Sc10

    by dslayer
    Replies
    15
    Views
    645

    yep happens like that, lol, but in other words,...

    yep happens like that, lol, but in other words, the sc10 is on a t4 chassis with buggy arms, i belive, so basicly it would be like driving a narrow t4, i would like to see one in person and test...
  10. Thread: Sc10

    by dslayer
    Replies
    15
    Views
    645

    its 179 for kit,

    its 179 for kit,
  11. Thread: Sc10

    by dslayer
    Replies
    15
    Views
    645

    i think it will be good because it has a lower...

    i think it will be good because it has a lower center of gravity, but i already have 3 slashs so im not going out of my way to get one, lol
  12. Replies
    13
    Views
    1,118

    they say it works with the yellow xl5 but i dont...

    they say it works with the yellow xl5 but i dont see why it dosent work with the blue one, the only diff is the cas color right?
  13. Replies
    14
    Views
    4,393

    i run a novak gtb with orion 10.5 brushless, i...

    i run a novak gtb with orion 10.5 brushless,
    i ran 18/96 when i first got it which made it hot,
    now i run 18/90 and dropped the temps alot, now i dont get over 174
  14. Replies
    2
    Views
    306

    a few qs about mmm

    few questions on the mmm,
    i am going to go brushless and so far the choice has been the mmm over the novak,,
    but does the mmm, come with built in lipo cutoff, the novak does not, you have to use a...
  15. Replies
    20
    Views
    659

    sounds like the sliper might be locking up, take...

    sounds like the sliper might be locking up, take the spur off and try pushing i both ways and see if it goes freely,
  16. Thread: Not impressed

    by dslayer
    Replies
    10
    Views
    496

    same, fit is bad and strength is bad

    same, fit is bad and strength is bad
  17. Replies
    14
    Views
    717

    yes they will fit

    yes they will fit
  18. Replies
    10
    Views
    1,089

    okay talked to novak on this, the 4s lvc will not...

    okay talked to novak on this, the 4s lvc will not work like this, it must use a 2s lvc for the diagram to work, or else it will try to pull the voltage all at once when you plug it in, just a fyi
  19. Replies
    10
    Views
    1,089

    forgot to mention, its only the black wire on the...

    forgot to mention, its only the black wire on the input harness that cooks itself
  20. Replies
    10
    Views
    1,089

    no, i took the lipo cut off completly off after...

    no, i took the lipo cut off completly off after everything happened, then replaced my input cord and tested to make sure the spcontrol was okay with my 7 cells to make sure i didnt damage it
  21. Replies
    10
    Views
    1,089

    thats what im waiting on, i already replaced the...

    thats what im waiting on, i already replaced the imput cord from the spcontroller, and tested with my 7 cells, everything is fine,
    but as far as lipo goes i woul really like to set it up, but not...
  22. Replies
    10
    Views
    1,089

    okay i did it just like the diagram, but having a...

    okay i did it just like the diagram, but having a big issue.
    i made sure that the speed control wire is pluged into smart stop, white red black so its the same on both sides like the instructions...
  23. Thread: lipo question

    by dslayer
    Replies
    3
    Views
    531

    lipo question

    if im running the evx-2 with 4 cell lipo cut off,

    i have one 30c 2s 5000 lipo and
    one 20c 2s 5000 lipo
    will i be okay running them togtheir?
  24. Replies
    2
    Views
    311

    novak lipo cut off part #

    whats the part number for the 2s lipo cut off that will work on the e revo, is it 5460?
    thanks
  25. Replies
    10
    Views
    1,089

    i hear you can run the 2cell cut off on just the...

    i hear you can run the 2cell cut off on just the bec side of the speed controller,
Results 1 to 25 of 118
Page 1 of 5 1 2 3 4