Search:

Type: Posts; User: TwiztidDevil

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    331

    It turned out to be the RPM Axle Carriers they...

    It turned out to be the RPM Axle Carriers they won't fit with the Traxxas Steel CVD axles. I used the stock 3.3 axle carriers with the RPM arms and it works just fine now. As far as to your question...
  2. Replies
    2
    Views
    244

    Pivot Ball Size

    Hi guys I am sorry if this has been covered before but I searched and couldn't find it. Does anyone know what size the Pivot balls are in the axle carriers/knuckles of a 3.3 Tmaxx. I recently bought...
  3. Replies
    5
    Views
    331

    Steel CVD's Won't Fit

    Hello guys as y'all know I've been working on my Tmaxx. It started as a 2.5 then after too much money I thought I was done.....then came the issues with the clutch bell, the tranny, and the diff's....
  4. Replies
    12
    Views
    383

    Thanks grizzly03 I appreciate the help. After...

    Thanks grizzly03 I appreciate the help. After some thought I found a 3.3 rolling chassis I am going to switch out the transmission, diffs, axles, and driveshafts. Hopefully that will help.

    Sent...
  5. Replies
    12
    Views
    383

    Yes the driveshafts turn and the wheels turn. The...

    Yes the driveshafts turn and the wheels turn. The more load I put on it the less they turn and the more it slips. Could it be the gears in the diffs? Would they go out at the same time?

    Sent from...
  6. Replies
    12
    Views
    383

    I put a single speed conversion in it when I...

    I put a single speed conversion in it when I broke the axle, thinking that maybe my problem was in the transmission but the gears I pulled out were just fine and it went together smoothly with the...
  7. Replies
    12
    Views
    383

    Ok I did as you requested. The clutch bell, spur...

    Ok I did as you requested. The clutch bell, spur gear, slipper nut, and brake disc are all turning as they should. I replaced the rear passenger side axle, but only the pieces that slide in and out....
  8. Replies
    12
    Views
    383

    Something is wrong......

    Hi guys I am having a new problem with my Tmaxx....... Thanks to the wonderful folks on here I've been able to fix all my problems I've been having. So I come to you guys again in my time of need.
    ...
  9. Replies
    14
    Views
    330

    Hi guys, my new double disc slipper with hardened...

    Hi guys, my new double disc slipper with hardened steel spur gear and the hardened steel clutch bell to match from Robinson Racing came in today. Hopefully the install goes well and using y'alls...
  10. Replies
    14
    Views
    330

    Thanks guys for the information, I really...

    Thanks guys for the information, I really appreciate it. I will do as you recommend. I will let you know how it goes.

    Sent from my SM-G970U using Tapatalk
  11. Replies
    14
    Views
    330

    Update....after putting the stock slipper back in...

    Update....after putting the stock slipper back in with a new plastic gear it made half a lap around the yard before the plastic gear was gone. I put the hardened steel gear on with the slipper clutch...
  12. Replies
    14
    Views
    330

    Thanks for the info!! This is my first nitro...

    Thanks for the info!! This is my first nitro vehicle and as I mentioned I removed the slipper clutches from crawlers. While it required me upgrading all the gears throughout the whole rig they both...
  13. Replies
    14
    Views
    330

    Sorry guys for the long delay been working 60...

    Sorry guys for the long delay been working 60 hours a week and haven't had much time to play. I finished the break in on my new engine it runs cooler and has A LOT more power than the original.

    I...
  14. Replies
    14
    Views
    330

    TwiztidDevil's TMaxx Build

    Bone stock 2.5 Tmaxx....my first nitro vehicle also my first basher. It was love at first sight. Got it home took it out of the box and for 2 days couldn't get it to start. Finally got mad and pulled...
Results 1 to 14 of 17