Search:

Type: Posts; User: bjoehandley

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. I’m shocked that I may not be the only person on...

    I’m shocked that I may not be the only person on this board that still has one of those combos!
  2. Iíve bought Fast Eddyís bearings for my Bandit,...

    Iíve bought Fast Eddyís bearings for my Bandit, Stampede, Clod, and Lunchbox, been thinking about getting a set for my SCX10 and have been thinking about getting Tamiya Dynahead and one of their...
  3. Thread: Maxx axles

    by bjoehandley
    Replies
    3
    Views
    708

    Probably not, the stockers are same size input...

    Probably not, the stockers are same size input and output as the 2wd and 4wd parts, you would be better off looking for ďsevere dutyĒ Slash 4x4 parts instead.
  4. Replies
    7
    Views
    540

    I haven’t run across clearance issues, but my...

    I haven’t run across clearance issues, but my Stampede uses an oooooolllldd New Era front bulked and the Bandit a RPM hollow piece that has the cavity filled with tungsten putty for pinewood derby...
  5. Replies
    7
    Views
    540

    If heís running front offset 2.8Ē wheels, he...

    If heís running front offset 2.8Ē wheels, he should be fine arm wise, body wise, itíll probably rub badly. Iím running the new Proline line belted Trenchers on the wheels with rear offset replaceable...
  6. Iím running 90/23 on my Bandit with Proline 2.2...

    Iím running 90/23 on my Bandit with Proline 2.2 Truck Prime M4 tires with a Sidewinder SCT/3800 combo on 3s.............once itís up to temp, itís rather violent at full throttle!
  7. Replies
    6
    Views
    1,598

    So what?! That’s common among a number of R/C...

    So what?! That’s common among a number of R/C manufacturers besides Traxxas as well as a large number of full scale platforms.
    The Chrysler sedan I daily shares a bunch of chassis parts with not...
  8. Replies
    11
    Views
    591

    What kind of surfaces are you running on? ...

    What kind of surfaces are you running on?

    Might be worth looking at some version of the Badlands instead of the Trencher, Iíd also look at
    Lowering the body as much as you can using the...
  9. Replies
    21
    Views
    1,041

    I like the tires a lot, though I will rotate them...

    I like the tires a lot, though I will rotate them before the next run, they’re starting to show some wear out back already.
  10. Replies
    21
    Views
    1,041

    Once I get more trigger time with it, it will...

    Once I get more trigger time with it, it will be.... I really need to stop by one of the local schools and test it out in a larger area before it gets too cold though.
  11. Replies
    4
    Views
    309

    Both of these! I’ve been usung one of these on...

    Both of these!

    I’ve been usung one of these on my Stampede for years now and it’s taken everything I’ve thrown the truck at and come back for more!...
  12. Replies
    21
    Views
    1,041

    Thanks Synnergy, it’s beyond just Rips! and is...

    Thanks Synnergy, it’s beyond just Rips! and is full blown bonkers once everything is up to temp and at full swing:eek:
  13. Replies
    21
    Views
    1,041

    Thanks SummitonSlingrs!

    Thanks SummitonSlingrs!
  14. Replies
    21
    Views
    1,041

    Took it for a test drive today..............and...

    Took it for a test drive today..............and itís....itís just NASTY:fear::thumbup:
    ...
  15. Replies
    21
    Views
    1,041

    RazorRC mentioned on a different forum that these...

    RazorRC mentioned on a different forum that these arms use SAE Hardware, which I had already discovered the hard way before I looked at that thread and luckily had a bunch of 4-40’s that fit for now,...
  16. Replies
    21
    Views
    1,041

    Quick update, found my missing 3s last week and...

    Quick update, found my missing 3s last week and took the Bandit out for a test, and discovered that the servo arm didn’t fit the servo (I’ll admit it, I’m a dummy, tried using a 25 spline servo arm...
  17. Got the parts in today, will give them a try when...

    Got the parts in today, will give them a try when I’m done with work today.
  18. I bought both of those servo arms, plus a pair of...

    I bought both of those servo arms, plus a pair of small front wings and a package of lead strips for some extra forward bite.
  19. I was looking over A-Main yesterday after making...

    I was looking over A-Main yesterday after making this thread too and did find these 2 that look like they might work, just need to order them first....
  20. HiTec servo arm for 4x4 Slash in 2wd Slash/Bandit/Rustler?!

    Does anybody know of a servo arm for the 2wd Slash and Rustler/Bandit with the 4x4 bell cranks and using a HiTec 645mg servo? Need that for my Bandit project that has an old 645mg in it and if there...
  21. Lol, yup! That looks about right, it even...

    Lol, yup! That looks about right, it even bounced off and kept going!
  22. Finally got the chance to run a pack through the...

    Finally got the chance to run a pack through the Hoss rear driveshafts and new slipper, very happy with the results!
    ...
  23. Try to pull it apart to see if it looks like mine...

    Try to pull it apart to see if it looks like mine Did, but before taking things apart, hold the spur still while pushing it on a high grip surface. If all the parts in the slipper stay still, but the...
  24. Replies
    11
    Views
    582

    IIRC, the lipos shouldn’t go below 3.7v per cell...

    IIRC, the lipos shouldn’t go below 3.7v per cell and typically max at 4.11v per cell when charged, so I would expect it to start cutting in at about 3.8v.
  25. Replies
    11
    Views
    582

    No problem, good to hear that did it!

    No problem, good to hear that did it!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4