Search:

Type: Posts; User: Busher Pusher

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    0
    Views
    206

    Will thet fit or not

    I would like to know if a crawler king body ( like the jeep ) will fit on a T maxx short wheel base 4910 with out making new mounting holes. I would like any help you could give
  2. Replies
    5
    Views
    290

    if i could get a close up picture of the receiver...

    if i could get a close up picture of the receiver box area of a 5308 with the AA battery setup that would be great.
  3. Replies
    5
    Views
    290

    i was hoping that the model 5308 used double A...

    i was hoping that the model 5308 used double A batteries and the battery tray would be a little taller for them ??
  4. Replies
    5
    Views
    290

    Battery box swap

    Can anyone tell me if the battery box from model 5308 will fit on model 5310 with out any modifications.
  5. Battery or charger what do you think (help)

    I have a Revo 5310 one of the Rx battery packs is only lasting 3min the outher lasts 7min one is about 3 yrs old but has been fine till today, the outher was new got it 2 yrs ago never charged it...
  6. Replies
    15
    Views
    980

    http://i262.photobucket.com/albums/ii119/wildfire1...

    http://i262.photobucket.com/albums/ii119/wildfire1958/chelsey/steering_0021.jpghttp://i262.photobucket.com/albums/ii119/wildfire1958/chelsey/steering_0012.jpgHere are the pic's i tryed to put in...
  7. Replies
    15
    Views
    980

    correct but when i did mine the turnbuckle no...

    correct but when i did mine the turnbuckle no long was running straight along the lower a arm had a angle two it. and the mounting point for the turnbuckle was lower on the new steering bellcrank...
  8. Replies
    15
    Views
    980

    tried to show pics can't seam to get it

    tried to show pics can't seam to get it
  9. Replies
    15
    Views
    980

    Here are a few pics of what i am talking about...

    Here are a few pics of what i am talking about does this help explain whats going on
  10. Replies
    15
    Views
    980

    I have the turnbuckles on the bottom side of the...

    I have the turnbuckles on the bottom side of the knuckle as they should be and the plastic crossbar sits on top of the idler and the crossbar end is upward with the turnbuckle installed only goes...
  11. Replies
    15
    Views
    980

    I am using the stock 4910 streering turnbuckles...

    I am using the stock 4910 streering turnbuckles which have the same rod ends on both ends no ofset like the 4907 is that what you mean.
  12. Replies
    15
    Views
    980

    Not to step on anyones toes, This is what i found...

    Not to step on anyones toes, This is what i found when i did my 4910 mod using 4907 style steering bellcrank. After the install i noticed a bumpsteer problem so after checking into the problem i...
  13. Traxxas Variable Damping Kit 5461 on T-maxx shocks ?

    Has anyone tried to use just the flexable restrictor pieces from the traxxas Variable Damping Kit 5461 to give T-Maxx shocks the dual damping like the GTR shocks on the Revo ???...
  14. Replies
    2
    Views
    389

    Thank You pntmachine i did call traxxas tech....

    Thank You pntmachine i did call traxxas tech. they did not know...
  15. Replies
    2
    Views
    389

    Revo shocks stock and GTR

    Could anyone tell me if the inside dia. on stock shocks and the GTR is the same. looking at traxxas Variable Damping Kit 5461 and wanted to know if it would work with stock type shocks. i have a...
  16. Replies
    1
    Views
    301

    Steering Bellcrank Upgrade

    Has any used the bellcrank system from a model 4907 on a 4910 classic, And what mods if any need to be done. Thank You
  17. Replies
    4
    Views
    877

    Hello. The easy start motor wires are black on...

    Hello. The easy start motor wires are black on bottom red on top and the motor from thr front turns counterclock wise
  18. Might try some kind of router bit bearing lube...

    Might try some kind of router bit bearing lube grease and oil will just collect the dirt dry type lube would be best
  19. Replies
    2
    Views
    384

    Out OF Storage Now

    Hello, I just bought one more TMaxx 4910 was in storage for two years. The old owner said they used after run oil but the motor turned over slow so i turned it over by hand and and spins but seamed...
  20. Replies
    2
    Views
    246

    Nirto Sport SE

    can anyone tell me if the new style sport bodys will fit the old style nitro sport se, with or with out mods. thank you
  21. Replies
    0
    Views
    1,948

    can anyone help ??

    hello I just picked up a NITRO SPORT SE has .15 engine this is what is going on . when the fuel line from the exhaust to the tank is hooked up it will not run seams like it pulls fuel away from the...
  22. Replies
    3
    Views
    237

    can any help out ??

    hello I just picked up a NITRO SPORT SE has .15 engine this is what is going on . when the fuel line from the exhaust to the tank is hooked up it will not run seams like it pulls fuel away from the...
  23. Replies
    9
    Views
    1,343

    evolution wheelie bar for t maxx

    Can anyone helpout ? I need to get a wheelie bar for my maxx and was looking at the Evolution 3 wheelie bar for t maxx part # T3718blue , can anyone tell me if its adjustable any how does it mount...
  24. Replies
    1
    Views
    307

    Exhaust Port O.D Size

    I am looking into putting a os 21tm in my T Maxx. And would like to run a rear exit pipe system like RD Logics but not sure if the O.D exhaust port size is the same on the OS 21tm and the Traxxas 3.3...
  25. Replies
    11
    Views
    1,486

    with out a muffler, no back pressure means no...

    with out a muffler, no back pressure means no fuel thats what puts pressure in the fuel tank and will push fuel to carb.
Results 1 to 25 of 33
Page 1 of 2 1 2