Search:

Type: Posts; User: mooseisloose57

Page 1 of 7 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    13
    Views
    448

    Aluminum skids will wear over time. IMO the cost...

    Aluminum skids will wear over time. IMO the cost would be close to the same considering the cost difference and the time the TRX's would last compared to the time the aluminum skid would last. I have...
  2. Also..... A MC59 plug is longer than an OS8. The...

    Also.....
    A MC59 plug is longer than an OS8. The OS8 would have a little less compression.
    Not sure of the length of the Traxxas plugs
  3. Replies
    7
    Views
    279

    Were you backing it out and back in all at the...

    Were you backing it out and back in all at the same time or backing it out a little at a time (1/12th to 1/8th turn) and making passes to see where the shift point is?
  4. Replies
    7
    Views
    279

    If the transmission doesn't shift, the first...

    If the transmission doesn't shift, the first thing I would check is how the shift point is adjusted. It may open fine when it is apart, but it could be adjusted too tight and the set screw needs to...
  5. How often are you having to change them? I've...

    How often are you having to change them?
    I've been using MC59 plugs first in a 2.5 and now my 3.3 Revo. No real issues over the past almost 4 years that I have had my Revo other than learning tuning...
  6. Replies
    23
    Views
    619

    I'm using a Sullivan Tigerdrive.

    I'm using a Sullivan Tigerdrive.
  7. Replies
    10
    Views
    430

    The song on the trailer for Mr Deeds has Journey...

    The song on the trailer for Mr Deeds has Journey playing Don't Stop Believin' I think. Hope this helps.
  8. Thread: anntena

    by mooseisloose57
    Replies
    15
    Views
    602

    I think it's 20 guage stranded wire

    I think it's 20 guage stranded wire
  9. Replies
    7
    Views
    412

    I have used RPM arm in the past. IMO they flex...

    I have used RPM arm in the past. IMO they flex too much to give consistent suspension action for racing. I went back to the stock arms and just keep spares in case I break one.
    If I was only using...
  10. Thread: anntena

    by mooseisloose57
    Replies
    15
    Views
    602

    I would think a hobby shop will have single...

    I would think a hobby shop will have single conductor "hookup wire" (mine does) It's small wire the same size as the antenna wire.
    I have used that in the past. Cut it to the right length and...
  11. Replies
    4
    Views
    421

    Mine does sometimes. I have been using a...

    Mine does sometimes. I have been using a Tigerdrive for almost 4 years and haven't had much of a problem with it.
  12. Replies
    24
    Views
    684

    It's the link in the first post

    It's the link in the first post
  13. Replies
    36
    Views
    1,371

    I have heard that it's possible for the engine to...

    I have heard that it's possible for the engine to run in reverse, but I would think that the timing would be off in relation to the crank.
  14. Replies
    18
    Views
    715

    I'm running a 1/8 style filter and I run a clean...

    I'm running a 1/8 style filter and I run a clean filter each heat and definitely a clean filter for the main.
    +1 on keeping the clean ones in a zip lock baggy
  15. Replies
    7
    Views
    511

    Yes. It has to do with the play in the hub where...

    Yes. It has to do with the play in the hub where the bearings are. It's possible that the wheel is tightened too much causing stress where the pin goes through the axle. RE: The first two pictures...
  16. Replies
    5
    Views
    373

    These may help...

    These may help
    http://www.traxxas.com/support/kb_search.php?action=artikel&cat=156&id=144
    There is a lot of information in the Traxxas Knowledge Center that helps me all the time. Check it out.
  17. Replies
    7
    Views
    511

    With the wear on the carrier it possibly could be...

    With the wear on the carrier it possibly could be that the wheel is too tight against the carrier. It may need to be shimmed to keep the hub from rubbing the carrier.
  18. Replies
    16
    Views
    483

    The header will not fit correctly with the EZ...

    The header will not fit correctly with the EZ start backplate. It's made to fit the 3.3 PE that has to use a starter box.
  19. Replies
    16
    Views
    483

    FYI the header will not attach as well with the...

    FYI the header will not attach as well with the starter backplate. I'm converting my 3.3 over to a starter box and have the spring header and it will not mount correctly without the standard...
  20. Replies
    10
    Views
    374

    Traxxas support has all the info you need....

    Traxxas support has all the info you need. Checkout "Support" at the top of the page and look under Revo.
  21. a good rule of thumb for the idle adjustment is...

    a good rule of thumb for the idle adjustment is the opening should be about the width of a paper clip wire
  22. That's where I would start.... even a little...

    That's where I would start.... even a little richer if the humidity is low.
  23. Replies
    5
    Views
    281

    Orange in the front and gold in the back is a...

    Orange in the front and gold in the back is a good starting point.
  24. Thread: Dx3r

    by mooseisloose57
    Replies
    16
    Views
    458

    I have a DX3 and I raced my Revo at a fairly...

    I have a DX3 and I raced my Revo at a fairly large track a couple of weeks ago with the antenna tube inside the body and had no problems with reception. You should do what you are most comfortable...
  25. Replies
    4
    Views
    290

    IMO get a Hitec 985. Not very costly and pleanty...

    IMO get a Hitec 985. Not very costly and pleanty of torque for a Revo.
Results 1 to 25 of 164
Page 1 of 7 1 2 3 4