Search:

Type: Posts; User: zengerg

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    15
    Views
    1,430

    It is a 6S ESC very similar to the VXL-8S ESC...

    It is a 6S ESC very similar to the VXL-8S ESC used in the X-Maxx. In fact, operation (the button, LEDs, etc.) is pretty much the same. However, I don't have any pointers to detailed 6S ESC...
  2. Replies
    15
    Views
    1,430

    It is a new ESC inside and out.

    It is a new ESC inside and out.
  3. Replies
    2
    Views
    234

    Give it a blip of throttle.

    Give it a blip of throttle.
  4. Thread: the compass

    by zengerg
    Replies
    4
    Views
    346

    Also, avoid flying close to RF radiation such as...

    Also, avoid flying close to RF radiation such as WiFi devices.
  5. Replies
    29
    Views
    4,200

    Please note that you need to put the original...

    Please note that you need to put the original X-Maxx RX in the truck. Its model is set to X-Maxx. Unless you programmed the Summit's RX model to X-Maxx (using a BT module and the Traxxas Link App)...
  6. Replies
    2
    Views
    307

    When I watch 1:1 race trucks, I see the drivers...

    When I watch 1:1 race trucks, I see the drivers compensate for the movements of the truck. Since you can't feel an RC car by the "seat of your pants", TSM makes up for that making control inputs...
  7. Replies
    9
    Views
    2,109

    Is the model set to stampede in the app and the...

    Is the model set to stampede in the app and the multifunction knob turned to the 12 o'clock position?
  8. Replies
    9
    Views
    430

    Hi, when you installed TSM did you set the model...

    Hi, when you installed TSM did you set the model with Bluetooth app to e-Revo? If the model is set correctly, the 50% setting (or 12 o'clock position) is optimal for the stock model on a normal...
  9. Replies
    4
    Views
    558

    If you use OTG (USB's on-the-go) cable to a USB...

    If you use OTG (USB's on-the-go) cable to a USB micro SD reader, you might be able to use the video on your phone without taking the back cover off. (Maybe this is the way you are already doing...
  10. Replies
    7
    Views
    1,954

    The new battery connector connects to the legacy...

    The new battery connector connects to the legacy Traxxas ESC (male) High Current Connector. You do not need an adapter.
  11. Replies
    5
    Views
    913

    Hi, for the non-ID case, the charger does not...

    Hi, for the non-ID case, the charger does not know the capacity of the battery and the proper charger rate.

    Do you know what current you are charging at? For this size battery, you should set it...
  12. Hi. I’ve been caught by this myself. The...

    Hi. I’ve been caught by this myself. The charger should only be plugged in without a battery connected.

    What I have found that works for me is the following:

    1. Unplug the battery from the...
  13. Replies
    11
    Views
    986

    L2 mode illuminates the high side of the quad...

    L2 mode illuminates the high side of the quad based on user input.

    Note that L2 is 3-state: tilt based->Press L2->all on->press L2->all off->press L2->tilt based

    To see how L2 works power...
  14. Replies
    1
    Views
    696

    After my nephew's Incredibles "That is totally...

    After my nephew's Incredibles "That is totally wicked!" exclaimation ... my favorite x3 and x5 flip quote: "OK, that's different."
  15. Replies
    28
    Views
    3,416

    With the light bar plugged in, you should be able...

    With the light bar plugged in, you should be able to reprogram the AUX buttons like you normally would. For example, you can set the other button for L1 (leg lights on-off)or L2 (leg lights...
  16. Replies
    25
    Views
    2,479

    To see fast spinning, have you performed the x3...

    To see fast spinning, have you performed the x3 and x5 flips in fast mode (expert 1)?
  17. Replies
    25
    Views
    2,479

    I believe that you do need to arm it before...

    I believe that you do need to arm it before applying throttle. Until you have the arm-throttle down pat, I would be careful what you throw it over -- i.e. don't start by throwing it out over the...
  18. Replies
    14
    Views
    1,707

    The sticks are in the bag with the extra rotors. ...

    The sticks are in the bag with the extra rotors. They can be hard really hard to see in the bag. If they are not hiding and really are missing from your box, please call support.
  19. Impressive damage. Sorry it happened.

    Impressive damage. Sorry it happened.
  20. Incredibly cool.

    Incredibly cool.
  21. Replies
    15
    Views
    966

    I believe it is the same. Entering the turn when...

    I believe it is the same. Entering the turn when you tilt towards the inside of the turn, you have to add more throttle to maintain altitude and accelerate sideways. As it turns, the rudder keeps...
  22. Replies
    15
    Views
    966

    Here is why I believe this happens. When you...

    Here is why I believe this happens. When you tilt the quad forward and accelerate, the air the quad moves through pushes back on the rotor disks. This pushes the quad down. (Imagine sticking your...
  23. Replies
    15
    Views
    966

    Hi. What do you mean by "dip down"? Lose...

    Hi.

    What do you mean by "dip down"? Lose altitude?
  24. Replies
    8
    Views
    868

    (I am an employee. I can nose-in hover but am...

    (I am an employee. I can nose-in hover but am not a great pilot and regularly hit things. Most frequently I hit the ground.)

    I really like it -- The LEDs and light pipes give it night and day...
  25. Replies
    3
    Views
    1,348

    Best rudder rate settings?

    What's the best setting for rudder? It defaults to 50. I've been flying at 73 following an expert's advice. (It must be perfect because its 73 not 75 :p ) I like how 73 spins but I turn smoother...
Results 1 to 25 of 41
Page 1 of 2 1 2