Search:

Type: Posts; User: CBerry

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    1,464

    Thanks olds97 and everyone else. We've decided on...

    Thanks olds97 and everyone else. We've decided on the Traxxas setup. The problem is lack of description on the charger. It will do off branded batteries but no where in the short description does it...
  2. Replies
    10
    Views
    1,464

    Someone correct me if I'm wrong here. Mah is the...

    Someone correct me if I'm wrong here. Mah is the fuel tank. Larger mah=larger fuel tank. 2S vrs 3S refers to voltage. 3S@5000mah=more speed, less range?
  3. Replies
    10
    Views
    1,464

    Olds97, I have a Hota Thunder AC6 charger, I...

    Olds97, I have a Hota Thunder AC6 charger, I don't have any issues with it. The one you linked to might be a decent one. I've been seeing trx ID cables. Do I need those to use a non traxxas battery...
  4. Replies
    10
    Views
    1,464

    Does a 2S battery pack 7600 mah give longer run...

    Does a 2S battery pack 7600 mah give longer run times than a 3S 5000 mah? I get that it runs slower with 2S pack, but who can control it, especially for a couple of novices?
  5. Replies
    10
    Views
    1,464

    Thank guys for the replies. Someone just informed...

    Thank guys for the replies. Someone just informed us that if we don't go with Traxxas batteries, it voids the warranty. I'll have to check on that.
  6. Replies
    10
    Views
    1,464

    E Revo VXL 1/10 recommendations

    Hey guys, I dont know squat about a e revo, I've never ran electric. I have the 3.3.

    A friend of mine is interested in the e revo and wants to know about battery recommendations. Should we buy...
  7. Factory assembled parts? Transmissions, diffs, etc

    I've been seeing what is described as factory assembled assemblies like trans and diffs etc and was wondering, are people buying complete RCs and parting them out?
  8. That little FRW/REV servo....its outta here. 🤣

    I got the Revo 3.3 back together. Found out I lost the inboard motor mount screw. That's what took out the spur gear. Put some lock tight on both now.

    So I was tightening the servo arm and...
  9. Replies
    6
    Views
    304

    The PHD button. Push Here Dummy. Thanks Grizz

    The PHD button. Push Here Dummy.

    Thanks Grizz
  10. Replies
    6
    Views
    304

    lol. I just figured out, all those settings...

    lol.

    I just figured out, all those settings in the manual that you can make on the controller, press this and then press that 4 times, you can do with the app. lol. I was afraid to mess with them...
  11. Replies
    6
    Views
    304

    Copy that Grizz, probably why it has never showed...

    Copy that Grizz, probably why it has never showed a speed over 34mph. Waiting on my parts delivery to test.
  12. Replies
    6
    Views
    304

    Telemetry app setup question

    Question, I was messing around with the app and noticed the tire setup was selected at 2.x. wouldn't the correct tire be the maxx 6.3?
  13. Replies
    12
    Views
    528

    Grizz. On mine the collar either slid down the...

    Grizz. On mine the collar either slid down the rod against the servo arm or it came that way. It does not make sense to me how this kept it open. When I hit the brake I could see the carb slide...
  14. Replies
    11
    Views
    471

    For what it's worth, I did not richen the LSN...

    For what it's worth, I did not richen the LSN needle last time I used it from a cold start when temps were in the low 50's. I had the tank empty and the lines purged and engine oiled after the last...
  15. Replies
    12
    Views
    528

    It's fixed guys. It was all in the linkage. I...

    It's fixed guys. It was all in the linkage. I have no gap now doctor G I'll add it in.
  16. Replies
    0
    Views
    194

    Took out my first spur gear today.

    So what's your opinion, metal gear or not? Most of my driving is in the desert, lots of rocks and debris. Took out one tooth, shaved the rest. I'm thinking it was...
  17. Replies
    12
    Views
    528

    It wasn't, the problem was in the servo box for...

    It wasn't, the problem was in the servo box for the throttle / brake box. Clue me in as I'm not sure of the terminology but the rod to the carb, has a stop, (round with set screw) apparently it moved...
  18. Replies
    12
    Views
    528

    I think I found it. Looks like the stop may have...

    I think I found it. Looks like the stop may have moved.

    http://imgur.com/a/1xUpUSW
  19. Replies
    12
    Views
    528

    When I engage the break idle falls

    Went out to the RC dirt track today and because I'm the , I most ran in the Midrange on the throttle and I could tell it was a bit rich. I leaned out the LSN then needed to lower the idle.

    Ling...
  20. Awesom Dr. G! Thank you. :D

    Awesom Dr. G! Thank you. :D
  21. When you say you run them down, I read someplace...

    When you say you run them down, I read someplace you should not discharge the NIMH pack. I'm using a Thunder AC6 charger. I charge the RX battery at a half amp. The charger has the availability to...
  22. What is your views on best battery charging practice?

    My NiCad stuff like a cordless drill, I've learned to let the battery drain down and not charge it until you lose power. My battery lasted about 5 years, in some cases months between charges.
    ...
  23. Cool, it seemed to be better. Last time out soon...

    Cool, it seemed to be better. Last time out soon as hit 6.3 volts via telemetry it starting losing the signal very soon after that. Thanks for the info.
  24. Well, if I have my chemistry right, gas has much...

    Well, if I have my chemistry right, gas has much more carbon in it than alcohol. Black is usually a result of being rich. I've always considered a nice gold color to be just right as far as engine...
  25. Replies
    11
    Views
    471

    I love my ez start. It's new however. We have...

    I love my ez start. It's new however. We have temps in the 50's here, to start mine I have to richen the low speed needle 1/2 to 3/4 turn richer for a fast start. If your fuel lines are purged plug...
Results 1 to 25 of 51
Page 1 of 3 1 2 3