Search:

Type: Posts; User: mastertheknife

Search: Search took 0.02 seconds.

  1. I have the VG chassis brace on my Slash LCG with...

    I have the VG chassis brace on my Slash LCG with OBA (68086-21), i like it.
    The reason i got it is because the LCG chassis is not as strong as the HCG chassis, and has a weak point in the front,...
  2. Thanks for the tip. For Loctite to work...

    Thanks for the tip.
    For Loctite to work properly, the screw and the hole should be clean of oil, grease and such, especially if using Loctite #242. The #243 is an improved formula, more resistant to...
  3. Replies
    9
    Views
    489

    The tips in this thread are very good. #1 - I am...

    The tips in this thread are very good.
    #1 - I am not sure if mixing grease with diff oil is a good idea.
    #3 - I can confirm that pushing the throttle with the truck on the side is a bad idea, been...
  4. Replies
    9
    Views
    631

    See this image from the manual:...

    See this image from the manual:
    http://i223.photobucket.com/albums/dd145/BSP06XRU/RC%20Stuff/VXL%20OBA_zpssbvg7mjm.png

    Basically, what you need to do is to connect the ESC input to CH2 instead of...
  5. Replies
    9
    Views
    489

    I noticed that if you reuse the gaskets...

    I noticed that if you reuse the gaskets (especially the black one between the gear and cup), it'll leak over time.
    I just serviced a diff recently. I replaced the cup, gaskets and everything from...
  6. Replies
    4
    Views
    375

    Try disconnecting the servo arm from the steering...

    Try disconnecting the servo arm from the steering bellcrank, as if you were disconnecting the front bulkhead from the chassis. There is a single hex screw underneath. On the LCG you need to turn the...
  7. When i bought my first slash, the store opened it...

    When i bought my first slash, the store opened it up and tightened it, said the slipper comes too loose from the factory.
    Its been a while, and i am still on the stock slipper, so far without...
  8. Replies
    232
    Views
    21,539

    Congratulations on the new house! By the way,...

    Congratulations on the new house!
    By the way, thats a good price! over here you can't find a 3 bedroom house below $200k in any city here.
    If its in the center of the country, thats minimum of...
  9. Replies
    10
    Views
    930

    Hi, By looking at the list of bearings in that...

    Hi,

    By looking at the list of bearings in that link, the 5 you are missing are these:
    1x 5x11x4mm bearing that sits in the slipper clutch (between the spur gear and the shaft)
    4x 5x8x2.5mm...
  10. Replies
    10
    Views
    930

    Hi, When we bought a used slash for my...

    Hi,

    When we bought a used slash for my brother, the wheels had some play in it.
    I replaced all bearings (slash has 21 in total, excluding the ones in the velineon motor, for that see 3352R) with...
  11. Replies
    17
    Views
    825

    I would check the bearings in that differential...

    I would check the bearings in that differential housing, especially the one the pinion gear sits in, perhaps it has too much play, allowing the pinion to move left and right and wearing the teeths...
  12. Replies
    2
    Views
    285

    From what i have noticed on my relatively new...

    From what i have noticed on my relatively new slash, the grease is more sensitive to temperature than the fluid.
    If judging by spinning a wheel (and letting the diff spin the other wheel in opposite...
Results 1 to 12 of 12