Search:

Type: Posts; User: grizzly03

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    7
    Views
    112

    In the picture above the grey transmission is...

    In the picture above the grey transmission is from a 3.3 T-maxx. The black transmission is from the classic, and it has a different spur gear/slipper clutch set up. The 70T spur gear was probably for...
  2. Replies
    16
    Views
    368

    The best part is around 14:44. "All the internet...

    The best part is around 14:44. "All the internet experts!"
  3. Replies
    43
    Views
    865

    The reason to use the Traxxas length horn: You...

    The reason to use the Traxxas length horn: You want to keep the drag link and the track bar parallel. The farther away from parallel they are the more the bump steer.
  4. Is the battery new or new to you/used? Are you...

    Is the battery new or new to you/used? Are you sure the battery is charged? It does sound like a bad battery.
  5. Replies
    10
    Views
    71

    Be sure to use the yellow and blue wire for the...

    Be sure to use the yellow and blue wire for the glow plug. The red and black for the starter. Both are separate circuits in the wand. If you try the blue wire with the black you get a lower voltage. ...
  6. Does this help? ...

    Does this help? traxxas.com/support/Hot-Electronics and traxxas/Overheating-electrics-and-gearing

    You can find more info under the support/troubleshooting tab under the vehicle model tabs.
  7. Replies
    13
    Views
    591

    It should work fine. The plastic case is actually...

    It should work fine. The plastic case is actually decent. Very little flex to it when I try to flex it with my hands. Also the fan blades are the same as the aluminum one. Looking at them only the...
  8. Replies
    101
    Views
    3,769

    It will be fine. The two out side holes are just...

    It will be fine. The two out side holes are just locating holes for the new linkage pivot post. The center one is the one for the screw that holds the pivot post. You are going to adjust the new...
  9. Replies
    13
    Views
    218

    Thank you. :thumbup:

    Thank you. :thumbup:
  10. Replies
    10
    Views
    71

    Another possibility is the blue wire. Check to...

    Another possibility is the blue wire. Check to make sure there are no cuts or exposed wire anywhere.
  11. Replies
    13
    Views
    218

    Did the ESC mount up in the oem location without...

    Did the ESC mount up in the oem location without modding the chassis? (hard to tell in the picture). When I used a Mamba Max Pro before I had it ziptied to the motor, LoL.
  12. The new bulkheads are a much better design. They...

    The new bulkheads are a much better design. They have a screw that holds the bulkheads and differential tighter together. The old style bulkheads didn't have this screw, that's why there were many...
  13. Replies
    13
    Views
    218

    That's good news. I think I found a sensored ESC...

    That's good news. I think I found a sensored ESC for my mini summit!
  14. Replies
    10
    Views
    71

    If you unhook the EZ-start motor (red/black...

    If you unhook the EZ-start motor (red/black wires) will the glow plug work then?
    It's possible to not be getting the required amps.
  15. Some of those bearings can be stuck. I have used...

    Some of those bearings can be stuck. I have used a thin shaft screwdriver to go through once side of the rocker to push the bearing out the other. You can catch the inside race to push the bearing...
  16. Here is a cheat sheet I made: ...

    Here is a cheat sheet I made:

    https://live.staticflickr.com/65535/50218682023_cbf62252ef_z.jpg[/url][url=https://www.flickr.com/photos/160449482@N07/]
  17. I have a savox 0250mg and i'm very happy with it.

    I have a savox 0250mg and i'm very happy with it.
  18. Replies
    6
    Views
    124

    That's a bummer! Glad you got it figured out...

    That's a bummer! Glad you got it figured out though.

    That's what I do for ESC's (and servos). I keep to what i've had good luck with (Traxxas,Castle,Tekin), even if they are a couple bucks more. I...
  19. Replies
    101
    Views
    3,769

    Congrats. You'll be happy. You should be able to...

    Congrats. You'll be happy. You should be able to use the aluminum pipe you have instead if the plastic one in the kit. I'm not a fan of the plastic pipes. Something about hot exhaust and plastic just...
  20. Replies
    5
    Views
    131

    That noise is normal because of the slow speed.

    That noise is normal because of the slow speed.
  21. Replies
    5
    Views
    284

    If you loosen the cap up a little bit you can...

    If you loosen the cap up a little bit you can feel the excessive play between the pivot ball and carrier. I tighten my caps just until the excess slop is gone and no more.
  22. If the receiver and ESC works with the servo...

    If the receiver and ESC works with the servo unplugged and the ESC plugged into CH1 (it works) and in CH2 (it works). But as soon as you plug in the servo (in either CH1 or CH2) it stops working that...
  23. Replies
    3
    Views
    152

    I would be happy if they would make a nitro...

    I would be happy if they would make a nitro engine boat again. Maybe the Spartan or M41 hull with a marine engine. :D
  24. Replies
    10
    Views
    175

    I think your best way of trying to make a speed...

    I think your best way of trying to make a speed run 1/16 mini is by going higher than 3s. You could go higher using the two battery compartments. Turn the punch down or accelerate slowly. Even...
  25. Replies
    6
    Views
    124

    I had a similar issue when I got my E-revo 2.0. I...

    I had a similar issue when I got my E-revo 2.0. I had a set of batteries that I used in my brushless summit. It has a T8 2000kv truggy motor with the RX8 ESC. The batteries worked fine even with the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4