Search:

Type: Posts; User: OS15CVPower

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    17
    Views
    832

    That holds the reverse idler gear in place

    That holds the reverse idler gear in place
  2. Replies
    21
    Views
    2,871

    Will it stay running with the glow ignitor...

    Will it stay running with the glow ignitor connected? The filter will need to be almost completely clogged to cause any running issues.
  3. Replies
    4
    Views
    181

    That depends on how hard you bash them. If you...

    That depends on how hard you bash them. If you are jumping and going fast over rough terrain then I would keep a set of front bulkheads, upper and lower arms, and shocks on hand at the minimum. If...
  4. Replies
    21
    Views
    2,871

    A loose exhaust can cause it to go lean at the...

    A loose exhaust can cause it to go lean at the top end. Also make sure your fuel tank lid is sealing so it doesn't bleed off exhaust pressure. Make sure all your fuel line is good.
  5. Replies
    21
    Views
    2,871

    Its hard to understand what you are saying but it...

    Its hard to understand what you are saying but it sounds lean to me.
  6. Replies
    3
    Views
    14,363

    The nitro urge is coming back now that spring is...

    The nitro urge is coming back now that spring is in the air. Nice pede I have one with a megatech .16 on it and mashers. Also have a few others I need to dust off. Currently working on putting a RB...
  7. Replies
    32
    Views
    3,691

    Agreed, $50 is a bargain. If it was mine I would...

    Agreed, $50 is a bargain. If it was mine I would tear down the whole truck and fix/replace any needed parts. That way you know what you have and know its solid.
  8. Replies
    4
    Views
    1,978

    Just leave the stock plastic driveshaft in the...

    Just leave the stock plastic driveshaft in the front. They don't see the torque that the rear does.
  9. Replies
    2
    Views
    1,007

    IMO thats half the fun of this hobby. I just...

    IMO thats half the fun of this hobby. I just bought a basket case nitro sport for $20 and have completely rebuilt it. Prob spent another $40 on parts plus some I had on hand. Also, your picture...
  10. Replies
    3
    Views
    1,164

    Yes and yes I would use the 3.3 flywheel and run...

    Yes and yes I would use the 3.3 flywheel and run stock gearing for now until after its broken in and it has full power. Then you can decide from there if it needs a gearing change. As for break-in, I...
  11. Replies
    7
    Views
    917

    Pics please, I would like to see that.

    Pics please, I would like to see that.
  12. The gap should be 0.7-1.0mm, not 1.7mm. About the...

    The gap should be 0.7-1.0mm, not 1.7mm. About the thickness of a large paper clip. Thats just a baseline and may need some tweaking to dial in the idle.
  13. If you want to keep reverse search for "no jerk...

    If you want to keep reverse search for "no jerk mod" It replaces the clutch with a pin for a positive forward engagement but I must warn you not to accidentally shift it while its moving. Or you can...
  14. Replies
    5
    Views
    2,042

    Sounds like its flooded if there is a lot of fuel...

    Sounds like its flooded if there is a lot of fuel in the exhaust. Pull the glow plug and spin then engine to clear the excess fuel. Once you get it running start leaning the HSN 1 hour at a...
  15. Replies
    3
    Views
    210

    It almost sounds like a diff is in backwards. To...

    It almost sounds like a diff is in backwards. To check hold the truck in the air and turn a rear wheel, the front should turn in the same direction. If the other rear wheel turns opposite then hold...
  16. Replies
    58
    Views
    2,256

    The sleeve is chrome plated. ABC= aluminum...

    The sleeve is chrome plated. ABC= aluminum piston, brass sleeve, chrome plated.
  17. Replies
    58
    Views
    2,256

    How does it run after the engine mods? To me it...

    How does it run after the engine mods? To me it looks like you cut too deep into the sleeve and got into the chrome. I have always heard thats a no-no because it changes the timing of the engine and...
  18. Replies
    35
    Views
    887

    Sounds like its lean on the LSN to me. I adjust...

    Sounds like its lean on the LSN to me. I adjust the throttle trim up to help with starting, like a fast idle on a 1:1 car.
  19. Replies
    35
    Views
    887

    Sorry but I dont agree. You shouldn't adjust the...

    Sorry but I dont agree. You shouldn't adjust the idle speed with the mixture screw. You should get the idle mixture correct and then adjust the speed with the idle gap screw. If the gap is too wide...
  20. Replies
    5
    Views
    695

    Losi 3.4 carb. Best thing I have done to my 3.3

    Losi 3.4 carb. Best thing I have done to my 3.3
  21. Replies
    38
    Views
    11,937

    Should I use 12 pegs or will 6 be enough??

    Should I use 12 pegs or will 6 be enough??
  22. Replies
    10
    Views
    596

    I've never tried traxxas fuel but from everything...

    I've never tried traxxas fuel but from everything I have read it has a LOT of oil in it and can be difficult to find the sweet spot. I run Byrons 20% in my rigs and they all run very good on it. I...
  23. Replies
    2
    Views
    464

    Heating it up with a hair dryer before starting...

    Heating it up with a hair dryer before starting will help too.
  24. Replies
    10
    Views
    596

    I feel your pain. I have been messing with nitro...

    I feel your pain. I have been messing with nitro since 2001 (duratrax ST Pro) and my current fleet is 4 and I rarely have all 4 of them running at the same time. Keep at it and just remember, its...
  25. Replies
    7
    Views
    698

    Losi 3.4 carb for sure. Best thing I did to my...

    Losi 3.4 carb for sure. Best thing I did to my 3.3.
Results 1 to 25 of 96
Page 1 of 4 1 2 3 4