Search:

Type: Posts; User: olds97_lss

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    4
    Views
    51

    For bashing, I usually have a little toe-out on...

    For bashing, I usually have a little toe-out on the front of my trucks. Makes them less "twitchy". With zero toe in/out, they wander pretty bad. With toe-in, they are more sensitive to input which...
  2. Replies
    4
    Views
    81

    There's a little clip that goes on the chassis...

    There's a little clip that goes on the chassis and holds the front neck of the diff in place. Actually, that was the nitro revos. The ERBEv1 has them molded into the bottom of the chassis.

    I'm...
  3. Replies
    12
    Views
    509

    I still use blue gel loctite on my slipper nuts....

    I still use blue gel loctite on my slipper nuts. Even when they are new, they sometimes like to walk themselves loose. Same with axle nuts.
  4. Replies
    9
    Views
    504

    You are not kidding! Some of these guys are...

    You are not kidding! Some of these guys are really hardcore with hundreds/thousands of $ worth of charging equipment.

    I bash alone, I typically take 2 trucks with me. I spend very little time not...
  5. Pretty sure you had your question answered, but...

    Pretty sure you had your question answered, but the front and rear differ from each another as well. I wish they were the same, then I wouldn't have to keep both on hand. I have to do the same thing...
  6. Replies
    18
    Views
    210

    Would be nice to have that many LHS's around. At...

    Would be nice to have that many LHS's around. At the peak in my area, there were 4 within 1 hours drive, now there are really only 2, one is 45 minutes, the other is 1 hour 10 minutes. The closer one...
  7. Replies
    19
    Views
    557

    That's what I did with my cheap bodies. Found it...

    That's what I did with my cheap bodies. Found it easiest to make a tower-to-tower brace with 3/4" aluminum box stock, then stack up something in the middle that would reach the top of the cab. Was...
  8. Replies
    6
    Views
    264

    I ordered mine from CNHL directly. They have 3 or...

    I ordered mine from CNHL directly. They have 3 or 4 "black series" 5000mah packs on their site, 2 with the 65C rating that are slightly different in size. I ordered the ones from the link I posted.
  9. Replies
    6
    Views
    264

    I ran hobbystar 3S 6200mah in mine and they...

    I ran hobbystar 3S 6200mah in mine and they barely fit without the battery clips. I now run CNH 5000mah black 65C and HRB 5000mah 50C in it. The extra weight of the 6200's was noticeable and harder...
  10. Replies
    2
    Views
    65

    4x4 or 2wd? Got a part # for the extensions?

    4x4 or 2wd? Got a part # for the extensions?
  11. Replies
    1
    Views
    93

    What did you work on or buy today?

    I've seen a few of these threads in specific forums and on other sites and thought they were fun to see/follow along. Figured maybe a more generalized one here might gain some traction, especially...
  12. Replies
    19
    Views
    557

    I've heard that it doesn't hold up that well. ...

    I've heard that it doesn't hold up that well.

    I run a probodyrc body on mine, but I'm running the slash chassis. It's holding up really well though. The one they suggest for the stampede 4x4 would...
  13. Replies
    11
    Views
    719

    I'm running a set of the standard 3.8 trenchers...

    I'm running a set of the standard 3.8 trenchers on my BB revo. It's holding up pretty good so far. I'm running stock revo axles/diffs in it with RRP steel in the transmission. Just have to try and...
  14. Replies
    3
    Views
    190

    What one guy likes, another may not. I run RC...

    What one guy likes, another may not. I run RC Raven springs, P2 rockers/rods (stock on 2.0), VDK #2 pistons with the valve on compression side, 70wt rear and 80wt front. Just updated my big block...
  15. I've had good luck with wax based lube on my...

    I've had good luck with wax based lube on my cvd's over the years. I use white lightning clean ride.
  16. Replies
    12
    Views
    88

    Working on them is about the same. Both are a bit...

    Working on them is about the same. Both are a bit of a pain to get at the diffs. Would be awesome if traxxas revamped the nitro revo to be like the latest brushless revo. Tougher driveline, easier to...
  17. Replies
    14
    Views
    399

    I'm not sure. My stock motor died after a few 3S...

    I'm not sure. My stock motor died after a few 3S runs in my eJato. I replaced it with a hobbystar 3660/3200kv and didn't notice a huge difference really in general performance. The HS 3660 ran a bit...
  18. Replies
    11
    Views
    719

    I think the MXL-6S is the same as the MM2. I...

    I think the MXL-6S is the same as the MM2. I don't believe the vxl-6s is though.



    I wish those were around 15+ years ago when I had a maxx. Would have liked to try them to see how they did. I...
  19. Replies
    8
    Views
    591

    This was the last one I bought:...

    This was the last one I bought:
    https://www.amazon.com/Venom-1600mAh-5-Cell-Receiver-Battery/dp/B000RRQPJG

    One of my revo's started as a slayer, my other started as a revo. I use a flat pack in...
  20. Replies
    14
    Views
    399

    It runs noticeably cooler in my eJato with the...

    It runs noticeably cooler in my eJato with the hobbystar 3665 3100kv than the vxl-3s/hobbystar 3660 3200kv I had in it. It ran warmer in my stampede. I have it geared taller now and put on higher...
  21. I switched to the 6890X early on. Thought it...

    I switched to the 6890X early on. Thought it would help facilitate cooling. Just had it off recently to replace the castle 4074 2200kv with an HPI Tork 4074 2200kv and it's still perfectly flat. I...
  22. Replies
    14
    Views
    399

    The max10 sct is pretty good, but the 3660SL...

    The max10 sct is pretty good, but the 3660SL motor it comes with tends to run hot. I ran it in my stampede for a while. It did better with the hobbystar 3665/3100kv motor than the 3660SL it came...
  23. FYI, pretty sure he's talking about just the...

    FYI, pretty sure he's talking about just the plate the motor bolts to. Not the mount/bearing holder piece.

    I have the kingheadz mount/bearing holder piece (which has a larger bearing than stock)...
  24. Replies
    7
    Views
    333

    Might be worth pulling the engine and checking...

    Might be worth pulling the engine and checking your clutch and bell bearings. If the bearings are dry/crunchy they will bind and instead of spinning, they will try spinning the tires. At idle,...
  25. Replies
    19
    Views
    557

    Sidewinder 3 is intended for 1/10th sized motors...

    Sidewinder 3 is intended for 1/10th sized motors I believe, so much over a 3665 sized motor is going to push it beyond it's capabilities. Even the sidewinder sct sv3 ran warm on a 3800kv 3660 motor...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4