Search:

Type: Posts; User: dgechrgr469

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    111

    Get a new pinion screw and clean it and the motor...

    Get a new pinion screw and clean it and the motor shaft with brake cleaner. I also use Robinson Racing Torx screws.

    Sent from my VS996 using Tapatalk
  2. The Slayer i have does not have dust boots and...

    The Slayer i have does not have dust boots and i've never had any problems. I don't think they're necessary.

    Sent from my VS996 using Tapatalk
  3. Replies
    30
    Views
    208

    Not sure if they will work myself. Sent from...

    Not sure if they will work myself.

    Sent from my VS996 using Tapatalk
  4. Recharge before you use them. I have had...

    Recharge before you use them. I have had batteries puff when I ran the voltage too low. Generally now I stop at 3.7v per cell.

    Sent from my VS996 using Tapatalk
  5. Replies
    30
    Views
    208

    Most of my Pro-Line arm mounts are 0 toe with...

    Most of my Pro-Line arm mounts are 0 toe with different amounts of anti-squat angles
    Not sure what the unmarked mounts are toe wise. You don't happen to have your rear arms switched around?
    ...
  6. Replies
    10
    Views
    137

    I used a receiver box that mounts up by the front...

    I used a receiver box that mounts up by the front bulkhead, forgot what model it's from.

    Sent from my VS996 using Tapatalk
  7. Replies
    10
    Views
    137

    I did the same but used velcro. Sent from my...

    I did the same but used velcro.

    Sent from my VS996 using Tapatalk
  8. Replies
    30
    Views
    208

    Like a Slash 2wd trans, thought so. Check if STRC...

    Like a Slash 2wd trans, thought so. Check if STRC has the bearing carriers. I'm at work or I could look at my cars.

    Sent from my VS996 using Tapatalk
  9. I believe that would be a good idea to put it in...

    I believe that would be a good idea to put it in storage mode until you're ready to use the battery again.

    Sent from my VS996 using Tapatalk
  10. Replies
    30
    Views
    208

    I'm not a Rustler/Bandit expert but if the...

    I'm not a Rustler/Bandit expert but if the transmission (gearbox) is the same as a Slash the brackets that the inner part of the arms connect to are part of the transmission and aren't adjustable....
  11. Replies
    30
    Views
    208

    Try switching your bearing carriers from side to...

    Try switching your bearing carriers from side to side.

    Sent from my VS996 using Tapatalk
  12. Replies
    30
    Views
    208

    It's a toe gauge, not sure he read the...

    It's a toe gauge, not sure he read the directions.


    Sent from my VS996 using Tapatalk
  13. Replies
    3
    Views
    81

    I have Spektrum, Tactic and Traxxas. It's a...

    I have Spektrum, Tactic and Traxxas. It's a personal preference of features and how it feels. I don't care for the exposed knobs on Traxxas radios that can get bumped out of adjustment. Tactic has...
  14. The latest and greatest are always going to sell...

    The latest and greatest are always going to sell for a premium, although those guys selling their trucks they bought new are still taking a loss. From what i've seen the "monster" Slashes bring about...
  15. Replies
    11
    Views
    324

    I'm going with Scorched Parts covers from AMain...

    I'm going with Scorched Parts covers from AMain as soon as LCG covers are back in stock. They are like inner fenders that keep debris from being thrown onto the chassis without covering the...
  16. Replies
    2
    Views
    152

    They won't rust but you need a high quality set...

    They won't rust but you need a high quality set of hex drivers because some of the lower quality s.s. screws are not as hard and will strip easily. I recommend getting MIP in 1.5 and 2mm.

    Sent...
  17. Use your antennae mast? Or you could buy some...

    Use your antennae mast? Or you could buy some Losi 22SCT battery brackets with the antennae mount on them and trim them to fit on your body or chassis with some antennae tube for a flag.

    Sent from...
  18. My only concern would be if you take the...

    My only concern would be if you take the "bumpers" off the front shocks you might bottom out the shock and possibly damage it somehow (broken piston/ shock cap). I would suggest leaving them in front...
  19. Replies
    9
    Views
    168

    Now that I clicked on the link I see that tool is...

    Now that I clicked on the link I see that tool is identical to mine. I got it from either AMain or Tower.

    Sent from my VS996 using Tapatalk
  20. Replies
    24
    Views
    1,025

    It works great doesn't it? Flexible to conform to...

    It works great doesn't it? Flexible to conform to the odd areas that bodies crack at and sticks well. I actually had to use a pliers to pull some off, that's how good this stuff sticks! I wish they...
  21. Replies
    9
    Views
    168

    They are very handy, besides working as a shock...

    They are very handy, besides working as a shock shaft pliers the tool I have has a feature for removing and installing the hollow balls on the shock ends. Very usefull for Traxxas style shocks.
    ...
  22. Race mode disables reverse, they frown on people...

    Race mode disables reverse, they frown on people backing up on the race track during a race.

    Sent from my VS996 using Tapatalk
  23. I'm guessing but is it possible to reverse your...

    I'm guessing but is it possible to reverse your motor rotation and the see if your esc is set to forward only?

    Sent from my VS996 using Tapatalk
  24. Replies
    3
    Views
    163

    Sounds like a weak servo or servo saver. With the...

    Sounds like a weak servo or servo saver. With the large amount of positive caster (kickup it's most commonly called on r/c cars) and the the gyroscopic force of the wheels spinning while going...
  25. Thread: Body clips

    by dgechrgr469
    Replies
    2
    Views
    287

    I don't know if Pro-line makes any body mounts...

    I don't know if Pro-line makes any body mounts for your truck, my experience is 1/10th Slashes.

    Sent from my VS996 using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4