Search:

Type: Posts; User: monello43

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. This happend to me but servo was fine. Is the...

    This happend to me but servo was fine. Is the light on your radio a steady green?
    If not, replace new batteries and then hold the set button.
    IdK why but my steering was veryy jerky when turning...
  2. Replies
    15
    Views
    1,129

    Yep, I think they will cover it bc its been about...

    Yep, I think they will cover it bc its been about 50 days but, the esc went the first day I had it so I wasn't runing it for three weeks till a new one was sent to me.
  3. Replies
    15
    Views
    1,129

    I was running a 2 s only one pack in heavy wet...

    I was running a 2 s only one pack in heavy wet snow, I wonder if that overworked the motor.
  4. Replies
    15
    Views
    1,129

    I Checked everything over, took entire car apart,...

    I Checked everything over, took entire car apart, I think the motor is half way shot.
    it seems like that's were the screetching noise is coming from, and sometimes it takes a couple seconds for...
  5. Replies
    15
    Views
    1,129

    My king headz motor mount bearing looks good, the...

    My king headz motor mount bearing looks good, the bearing in slipper looks good, adjusted the nut on slipper, how it's suppose to be.
    I did notice the three pads in slipper were a bit scuffed up...
  6. Replies
    15
    Views
    1,129

    I bearings in slipper and motor mount look good...

    I bearings in slipper and motor mount look good but I did notice the three pads look a bit scuffed up?
  7. Replies
    15
    Views
    1,129

    High pitch sound?

    Anyone have any idea why in forward or reverse there is a very high pitch screetching sound.
    I checked slipper, motor pinion is touching gear and it's not stripped. tried putting on differential...
  8. Oh real simple, if you take the back off by just...

    Oh real simple, if you take the back off by just removing the four screws.
    You will see that the the motor mount plate covers a quarter of the hole where you insert the larger tube where center...
  9. Replies
    20
    Views
    750

    Is that a proline desert rat how is that body for...

    Is that a proline desert rat how is that body for bashing
  10. Thread: body

    by monello43
    Replies
    4
    Views
    412

    Depends, if you just race the flotek I think is...

    Depends, if you just race the flotek I think is great, but if you bash with all the cutouts I would go with something else
  11. Idk who started this mod, not me, but definitley...

    Idk who started this mod, not me, but definitley the best one for driveshaft I can say.
    I have seen pics if others that have done this want to chime in.
    I actually used the carbon fiber tube, looks...
  12. Figured it out! Simply cut tube 9 and 9/16...

    Figured it out! Simply cut tube 9 and 9/16 inches. It's a perfect fit from front to back.
    You just have to shave a bit off the motor mount plate for tube to slide through motor mount hole (use a...
  13. Replies
    20
    Views
    484

    sounds like usual sticky button issue, its...

    sounds like usual sticky button issue, its cycling modes... needs repair
  14. How do you intall alluminum tube mod for driveshaft

    I was wondering if I cut the alluminum tube basically the same size as center driveshaft.
    Also, anything else I need to do or any link on how to do this would be great.
    I have the king headz motor...
  15. Replies
    163
    Views
    23,033

    Hey Grn, about how long did you cut the carbon...

    Hey Grn, about how long did you cut the carbon fibor shaft in comparision to the center driveshaft, same length or longer.
  16. Replies
    11
    Views
    615

    When mine start to go I will order a set of yeah...

    When mine start to go I will order a set of yeah racing bearings, I have heard they are very good and maintenance free just about. They are about twenty bucks for the kit shipped ...
  17. Replies
    17
    Views
    1,146

    just replace em easier very cheap too

    just replace em easier very cheap too
  18. Replies
    12
    Views
    536

    rpm a arms and nerf bars for bashing

    rpm a arms and nerf bars for bashing
  19. Yea I do like that but I think Integy or another...

    Yea I do like that but I think Integy or another company makes a more robust type metal grill instead of just the clear plastic fins
  20. Yea, I know about the one fan, any links on a...

    Yea, I know about the one fan, any links on a good fan.
    I use it with outerwears but a bit of water and slight dirt still gets in, so needs to be durable thanks.
  21. Recommendation on a good motor fan heatsink

    I'm running only 2s, stock gearing, slipper, esc fan, temps in twenties, and I run it hard threw the grass and motor is super hot after maybe 10-15 min(I don't have a temp gauge but very hot to...
  22. Trenchers best all around tire, ton of tread too....

    Trenchers best all around tire, ton of tread too. They also come pre mounted on wheel also making it easy.
    Prolines most popular tire.
  23. Thread: Snow bash

    by monello43
    Replies
    3
    Views
    255

    Yep, looks like fun we run ours in snow all the...

    Yep, looks like fun we run ours in snow all the time. Just suggest for u to get an outerwears, then I use dry Moo-slick on bearings every so often so they don't rust up.
    I havent had one fail yet...
  24. Thread: slash body

    by monello43
    Replies
    8
    Views
    1,482

    buy a set of rpm adjustable body post it will...

    buy a set of rpm adjustable body post it will raise body almost an inch. I did this with proline trencher tires with stock body and alot better.
  25. I was goin to go stainless but they are just to...

    I was goin to go stainless but they are just to soft and strip. Went with tonys screws cheap and stronger then stock.
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4