Search:

Type: Posts; User: olds97_lss

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    3
    Views
    74

    Probably to mount the plate to the truck. The...

    Probably to mount the plate to the truck. The holes in the bottom of the esc's are very shallow. When I do have those, I typically drill the holes in the plate to match, then add dual sided tape,...
  2. I haven't stepped up to that long yet, but I run...

    I haven't stepped up to that long yet, but I run a hobbystar 3665 3100kv off my vlx-3s esc on 3S without much drama.
  3. Replies
    8
    Views
    119

    Got a link to one that works on screws this...

    Got a link to one that works on screws this small? 2mm button heads don't leave a lot of material to work with, similar with 2mm flathead screws.
  4. Replies
    321
    Views
    40,082

    Even on 2S with the stock system, the stock...

    Even on 2S with the stock system, the stock plastic ones didn't hold up long for me on my stampede... I was even running the traxxas 2.8 chevrons on it. Glad I bit the bullet early and just went with...
  5. Replies
    4
    Views
    49

    Could probably go to your local ace/doitbest...

    Could probably go to your local ace/doitbest hardware store and find a tiny roll pin to replace it. Probably longer, but that can be remedied with a dremel. I know my doitbest hardware store has a...
  6. I made a 2 disk setup for mine, it was totally...

    I made a 2 disk setup for mine, it was totally hack, but it helped a lot. Not sure what cross bar your talking about though. I had a spare brake disk from something and the X piece/hub it rode on. I...
  7. Replies
    16
    Views
    249

    Nope. I asked them 3-4 months ago and that's...

    Nope. I asked them 3-4 months ago and that's pretty much what they said. I don't know if they didn't hold up any better than stock or what, but I replace all 4 of mine at least once a season due to...
  8. Replies
    16
    Views
    249

    I didn't really notice a big difference in...

    I didn't really notice a big difference in agility or anything. When I first got my 2.0, it was a roller and I moved over a lot of stuff from my 1.0. I never ran the 2.0 on 4S, only 6S and I never...
  9. I ran 18/56 with trencher 3.8's on my v1 for a...

    I ran 18/56 with trencher 3.8's on my v1 for a while on 4S. Didn't seem to need a motor fan. Had the stock v1 motor and esc (MXL-6S). Prior to that I ran 18/64 for 2 years.
  10. Chassis hits the ground and I can lift the tire...

    Chassis hits the ground and I can lift the tire 1/2" or so once the chassis bottoms out before the shock fully compresses. The shocks are stopping the arms from dropping, running the GTR's.

    New...
  11. Replies
    29
    Views
    522

    Did you post a question about that somewhere?...

    Did you post a question about that somewhere? Glad you figured it out!
  12. Replies
    3
    Views
    133

    Expected that to happen. He's nearly folded his...

    Expected that to happen. He's nearly folded his x-maxx in half more than once. Running WOT and hitting a truck axle with the bottom of the chassis in flight would definitely do it!

    I busted my...
  13. Replies
    6
    Views
    127

    Yep, I was. Didn't see the MX38, just saw...

    Yep, I was. Didn't see the MX38, just saw badlands and my brain stopped reading. lol! The MX38's are heavier than stock as well. 14.6oz vs 13.9oz of the ext's.
  14. Replies
    6
    Views
    127

    I can't imagine the tires are causing the issue....

    I can't imagine the tires are causing the issue. They are far lighter and smaller OD than the stock tires, so the motor/esc shouldn't have to work as hard with them.
  15. Seems like there were at least 2 versions of arms...

    Seems like there were at least 2 versions of arms that fit, one with sway bar holes, one without and now the 3rd "cold weather" heavy duty version. I went with the latter. Supposed to be more...
  16. Replies
    18
    Views
    1,066

    Running 19/54 with trencher 2.8's. I ran into...

    Running 19/54 with trencher 2.8's. I ran into similar heat issues when I was running 4S in my outcast (same esc). Without the fan, the motor got up to 160F. I was running it in grass quite a bit at...
  17. Ordered a couple sets of 3655P. I wanted orange,...

    Ordered a couple sets of 3655P. I wanted orange, but didn't want to pay what was asked, so got the blue ones instead. Will see how they do.
  18. Replies
    18
    Views
    1,066

    I wondered why there were so may 4k+ motors...

    I wondered why there were so may 4k+ motors available. Didn't make any sense to me. Especially since I seem to cook anything that is 3200kv or more in any of my trucks without trying too hard on 3S....
  19. Sounds like a plan. Guessing the rustler 4x4 are...

    Sounds like a plan. Guessing the rustler 4x4 are the latest/greatest to run? I broke a couple stock ones early on which is why I went with RPM to begin with.
  20. Rear inside upper ball ends popping off...

    I can't figure out what causes this, but in never fails. Every time I check, the rear upper/inside ball ends on the turnbuckle are popped off the pivot balls. I have a washer on keeping them...
  21. Thread: Too much?

    by olds97_lss
    Replies
    1
    Views
    278

    Nitro revo to e-revo? Nitro trans/diffs/axles?...

    Nitro revo to e-revo? Nitro trans/diffs/axles? Planning on 4S or 6S? What's the motor physical size?

    It would likely be fine in a 2.0 e-revo. I run a max6 160A esc/2050kv 4074 in my 2.0 at the...
  22. Replies
    7
    Views
    97

    isdt makes a couple, 80w/8A and 200W/25A:...

    isdt makes a couple, 80w/8A and 200W/25A:
    https://www.amazon.com/ISDT-Discharger-Discharing-Capacity-Discharging/dp/B07VS2JSN9

    skyrc also has one, 200W/30A:...
  23. After a short time, the bushings wear, which...

    After a short time, the bushings wear, which causes slop and binding. Having bearings keeps the pivot running true for a lot longer without binding or gaining slop. With so little available movement,...
  24. Replies
    16
    Views
    1,122

    Good to know. I didn't know it made it so you...

    Good to know. I didn't know it made it so you couldn't run sway bars. I recently installed those on mine. Then again, running squishy RPM arms likely negates any benefit I get from the sway bars......
  25. Replies
    5
    Views
    128

    I use adapters on my charger without issue up to...

    I use adapters on my charger without issue up to 10A (charger is 4x10A/4x100W). It's actually kind of stupid at this point as everything I have now has XT90's on it. The charger came with 2xEC3 and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4