Search:

Type: Posts; User: BadlandsMike

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    12
    Views
    959

    My used xmaxx just sheared 5 teeth off the spur...

    My used xmaxx just sheared 5 teeth off the spur the other day. Not exactly sure why but my guess was from wear? However the spur slides on the bearing shaft quite a bit, not sure it’s normal. Ended...
  2. Replies
    1
    Views
    276

    X-MAXX time!

    Been a while since I last posted but just wanted to say thanks for all the info you guys have been sharing with all your R&D. So anyway I picked up a used 8SMAXX recently from my local hobby...
  3. Thread: Gearing

    by BadlandsMike
    Replies
    4
    Views
    1,396

    Thanks for sharing your gearing info, still...

    Thanks for sharing your gearing info, still waiting on more interest from my club to race these, fingers still crossed for that to happen. I still think it would be a fun somewhat inexpensive...
  4. Replies
    28
    Views
    2,939

    Stripped the gears in my 4tec. Metal gear kit...

    Stripped the gears in my 4tec. Metal gear kit ordered so will be updating my 2075. $20 for a gear set or you can buy them with new with installed for 50. Was a mine incident and mine blew. Have not...
  5. Replies
    9
    Views
    1,127

    At least you got a set of lights. I ordered a set...

    At least you got a set of lights. I ordered a set from my local hobby store over a month ago. Not sure what the issue is!
  6. Replies
    13
    Views
    3,038

    Thanks for sharing the info. I have hardly driven...

    Thanks for sharing the info. I have hardly driven mine at our local carpet track. Stripped the plastic servo gears last nite. They need to put metal gears in the 2075s. Slid into a wall and money...
  7. Replies
    8
    Views
    3,032

    I have seen the sway bar kits on eBay. I have...

    I have seen the sway bar kits on eBay. I have trying to get more people at my local track to race these still no luck yet.
  8. Replies
    2
    Views
    638

    What gearing are you using? Also are metal motor...

    What gearing are you using? Also are metal motor mounts or cooling fans allowed, just might help out enough. Are they 5 min. Races?
  9. Replies
    28
    Views
    2,939

    There is a metal gear set you can get for the...

    There is a metal gear set you can get for the 2075. Oops just noticed this was mentioned. Still waking up apparently.
  10. Replies
    9
    Views
    3,872

    I believe you are correct... Steel drive instead...

    I believe you are correct... Steel drive instead of the alum. I have a brushed GT, figured I would just upgrade for future uses.
  11. Replies
    41
    Views
    6,695

    Who makes the Z06? Is it an RC? Just curious if...

    Who makes the Z06? Is it an RC? Just curious if you know the manufacturer.
  12. Replies
    4
    Views
    895

    Took it out to the track last nite! Only got a...

    Took it out to the track last nite! Only got a chance to do some test laps (4 mins or so) on the oval setup but I was very impressed how it handled. Thought I may have to scuff the tires but they...
  13. Replies
    3
    Views
    904

    Thanks bash! Looking at picking up a couple...

    Thanks bash! Looking at picking up a couple different ones. Would rather not destroy the GT one. Although I don't buy these to just sit on the shelf. My original 4x4 slash fox body and my carpet...
  14. Replies
    3
    Views
    904

    Vaterra bodies?

    Do the Vaterra 1/10 bodies work? Specifically the 69 camaro? Have been doing a lot of body searching to find ones that work.
    I did see a Facebook GT forum that I have not investigated fully. Not to...
  15. Replies
    17
    Views
    2,078

    I noticed mine seems off as well. Adjusted the...

    I noticed mine seems off as well. Adjusted the trim on the controller. Have not tested other than driving in my basement (not much room) will look into it more. Good to see more people picking these...
  16. Replies
    4
    Views
    895

    Picked up a brushed Ford GT!

    Well after my questions I finally picked up a Blue GT. Planning on trying to get my club to start up a stock brushed class. Fingers crossed. There are a few that have these so I will try to talk them...
  17. Replies
    8
    Views
    1,187

    Maybe some course scotch bright or scouring...

    Maybe some course scotch bright or scouring pad... 0 ott steel wool?
    So does everyone run brushed motors?
  18. Replies
    8
    Views
    1,187

    Good job. 13 4tecs would be pretty cool to see...

    Good job. 13 4tecs would be pretty cool to see racing. What type of bodies? As far as scuffing the tires what was the best solution?
  19. Replies
    9
    Views
    2,699

    Voltage - for some reason I get confused :) Also...

    Voltage - for some reason I get confused :)
    Also this GT forum seems to be pretty slow? Is the car just not selling? I see they lowered the price as well (Traxxas)
  20. Replies
    9
    Views
    2,699

    bash- you made the same comments that I want to...

    bash- you made the same comments that I want to happen. A GT class of its own. There have been a couple sold at the local HS that I know of but I keep trying to get more interested. But hopefully...
  21. Replies
    9
    Views
    2,699

    Racing a GT in a 25.5 VTA class?

    Been thinking of getting the 4tec 2.0 brushless version and substituting to a 25.5 motor to run at our local carpet track. Are there any people who actually race these in VTA? Seems most just do...
  22. Replies
    13
    Views
    837

    Thesmog do you have the 2075 with OEM gears?

    Thesmog do you have the 2075 with OEM gears?
  23. Replies
    13
    Views
    837

    Btw if I would learn to drive better it would...

    Btw if I would learn to drive better it would probably help! :)
  24. Replies
    13
    Views
    837

    Unfortunately I did not have that option since I...

    Unfortunately I did not have that option since I broke it before the strc install. So I assume it is just an adjustment guess at this point? I did a search on here and found the metal replacement...
  25. Replies
    13
    Views
    837

    I installed these when I broke the plastic link...

    I installed these when I broke the plastic link twice but I must have dialed the spring tension to much because I stripped the servo gears in the 1st race. Is there a way to tell how much a person...
Results 1 to 25 of 41
Page 1 of 2 1 2