Search:

Type: Posts; User: jarod_rodriguez

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    13
    Views
    599

    It is pre-programmed to be throttle neutral from...

    It is pre-programmed to be throttle neutral from the factory but can be completely disabled (Bad IMO). Check the manual, search for fail-safe in the PDF. I can't remember if you can set the default...
  2. Replies
    13
    Views
    599

    Looks like the brake is engaged or it is stuck in...

    Looks like the brake is engaged or it is stuck in reverse of the tranny is has bits in it for the reverse gear breaking apart. I have mine programmed to auto lock the brake to prevent runaway when...
  3. Replies
    3
    Views
    1,553

    Here is a pic of the diff all put together and...

    Here is a pic of the diff all put together and secured to the only point that it actually moves. If you can see how far the lip is out. It should be flush and pretty no lip.
    ...
  4. Replies
    3
    Views
    1,553

    Nope, not spacers at all. Correct, I put in the...

    Nope, not spacers at all. Correct, I put in the new x-rings (blue silicon) in the x-ring cup, then I put in the new PTFE washer next, then the spider gear and e-clip. No slop or play so it feels...
  5. Replies
    3
    Views
    1,553

    Rear Diff Rebuild and Binding Issue

    After tearing everything apart and cleaning it up, I installed the steel CVD kit. However, when I put it all back together and tighten it down. It is 100% bound up. Wont budge, I have to back the...
  6. Replies
    2
    Views
    159

    ok, that is what I thought. I will clean it out...

    ok, that is what I thought. I will clean it out and put a tab of while lith in it.
  7. Replies
    2
    Views
    159

    Rear bulkhead lubrication?

    I am in rebuilding the rear end on the Jato and it has been a few years since I have done this. I noticed that there was absolutely ZERO grease in there. Is this thing supposed to be bone dry?...
  8. Replies
    4
    Views
    556

    The serviceability could be much informed on this...

    The serviceability could be much informed on this truck. Having rebuilt this thing 3 or 4 times from top to bottom leaves a lot to be desired. Way too many screws for a car this size and some areas...
  9. Replies
    23
    Views
    1,393

    Agreed, I fired up 2 of my nitro's this weekend...

    Agreed, I fired up 2 of my nitro's this weekend while the kids ran their electric. Even after sitting for almost a year, they fired right up and ran at least 4 tanks through both of them. I get the...
  10. I went back with the good old white lithium...

    I went back with the good old white lithium again. it seemed to work well enough. Although, I may have used too much diff fluid in the diff's. I have a hard pull left under full throttle that I...
  11. 7138X installation question regarding left handed thread orientation

    I know the recommendation is to have the left handed thread side all towards 1 side of the chassis to make it convenient and easy to remember which way to turn the buckle. Which way do you guys...
  12. White Lithium Grease vs. Synthetic Grease with PTFE?

    Which do you prefer? pros/cons? I am rebuilding my bulkheads again and noticed I used white lithium grease last time but I would say it was 90% gone. I have both and use Super Lube Synthetic Grease...
  13. Replies
    1
    Views
    128

    Please ignore this. I'm a blind idiot today for...

    Please ignore this. I'm a blind idiot today for some reason. I found them in plain sight. SMH!
  14. Replies
    1
    Views
    128

    Link to build diagrams?

    I can't seem to locate the complete diagrams for this on the support site anymore. I am in need of them so I can rebuild this thing and can tell which screws go where. Any help is really...
  15. I have had mine for 6+ years, including at least...

    I have had mine for 6+ years, including at least 2 or 3 complete rebuilds. In the process of rebuilding again and have never had any issues after I put the center diff in. I use heavier weight diff...
  16. A very true statement. I have been doing this a...

    A very true statement. I have been doing this a for a number years now and have been good about my spending lately but early on and 8 cars/trucks later it was a huge investment. This Jato was custom...
  17. Starting not to be cost effective. LOL.

    Starting not to be cost effective. LOL.
  18. Cool, thanks! Sent from my iPhone using...

    Cool, thanks!


    Sent from my iPhone using Tapatalk Pro
  19. Where might I find one of those? Or will it need...

    Where might I find one of those? Or will it need to be custom milled?


    Sent from my iPhone using Tapatalk Pro
  20. Will this motor fit my Jato without mod?

    Just curious if this will fit without any major work?
    ...
  21. Replies
    6
    Views
    273

    Yep. Sent from my iPhone using Tapatalk Pro

    Yep.


    Sent from my iPhone using Tapatalk Pro
  22. Replies
    6
    Views
    273

    I know, I was just being funny. It's gotta be a...

    I know, I was just being funny. It's gotta be a place that has at least 4 screws to hold something down.


    Sent from my iPhone using Tapatalk Pro
  23. Replies
    6
    Views
    273

    Uh, one is the glow plug. The other 2 screws......

    Uh, one is the glow plug. The other 2 screws... no clue. They could in a 100 places on that truck. :-).


    Sent from my iPhone using Tapatalk Pro
  24. Replies
    2
    Views
    231

    Shouldn't be an issue. Sent from my iPhone...

    Shouldn't be an issue.


    Sent from my iPhone using Tapatalk Pro
  25. Total feel. Not sloppy loose and not too tight...

    Total feel. Not sloppy loose and not too tight that it feels like it is binding when you roll it. Needs to feel somewhat snug. Hard to explain but have never stripped a gear. Also having the slipper...
Results 1 to 25 of 480
Page 1 of 20 1 2 3 4