Search:

Type: Posts; User: gunnuts

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. My FPV gear is pretty darn fast. I use it to...

    My FPV gear is pretty darn fast. I use it to freestyle fly quadcopters in tight spaces going fast.
    The limitation will likely be in video transmission as current FPV gear is supposed to be above...
  2. Replies
    46
    Views
    1,672

    LOL funny thing... I setup a ramp in front of my...

    LOL funny thing... I setup a ramp in front of my house this Sunday. While I was charging batteries I gave my XMaxx a once over and my front right inner seal had popped off. I ended up taking it apart...
  3. Replies
    46
    Views
    1,672

    I keep seeing people talk about this seal coming...

    I keep seeing people talk about this seal coming off.
    I took my XMaxx apart to service these bearings and couldn't get the cover off to clean and lube mine.
    I guess I'll have to keep trying to get...
  4. Replies
    18
    Views
    813

    I just remove 1 or two 1 inch pieces of the...

    I just remove 1 or two 1 inch pieces of the gasket.
    That way it will still close right and NOT hold pressure.
    Then I put it somewhere non flamable. I likes me some cinder blocks... I guess I never...
  5. Replies
    11
    Views
    474

    My dad gave me a Tamiya Frog when I was about 17....

    My dad gave me a Tamiya Frog when I was about 17.
    Darn near burned my 68 Charger to the ground charging batteries w/ a wind timer under the hood.
    That was MANY thousands of RC dollars ago. I...
  6. Replies
    18
    Views
    813

    I use a battery checker to "inspect" my...

    I use a battery checker to "inspect" my batteries. The internal resistance should match between cells and be LOW.
    All lipos should be stored like you are about to have a fire. I use ammo cans and...
  7. Thread: VXL Drag Build

    by gunnuts
    Replies
    0
    Views
    73

    VXL Drag Build

    I purchased a new VXL to make myself a drag car this weekend.
    I already have the LCG chassis and some tires...I planned to rip it apart the moment I got it.
    Then I took it out of the box...all...
  8. Replies
    13
    Views
    5,097

    I call it efficiency.

    I call it efficiency.
  9. Replies
    46
    Views
    1,327

    My almost new slash 4x4 has this same kinda...

    My almost new slash 4x4 has this same kinda movement.... mine goes strait though.
  10. Thread: Xmaxx and BEC

    by gunnuts
    Replies
    19
    Views
    1,151

    No I never moved forward with BEC as I have LOTS...

    No I never moved forward with BEC as I have LOTS of small lipos.
    Still tweakin my first mount to make everything fit.
  11. Thread: Drag Rustler

    by gunnuts
    Replies
    26
    Views
    823

    I follow some guys here in northern CA that run...

    I follow some guys here in northern CA that run pro line transmissions.
    If your as fast as they are and not blowing transmissions its a solid product.
  12. Thread: Wheel wobble

    by gunnuts
    Replies
    5
    Views
    282

    I regularly bend my axles. I run in the street...

    I regularly bend my axles. I run in the street alot and almost every time I clip something hard I bend an axle.
    I have gotten very good at replacing them.
  13. Replies
    14
    Views
    655

    ooooohhhhh look how clean that slash is! I like...

    ooooohhhhh look how clean that slash is! I like how that fan fits. Are both fans running from the receiver or do you use a BEC?
  14. Replies
    10
    Views
    390

    Vinyl it a great idea... if you can work with it...

    Vinyl it a great idea... if you can work with it on a transfer sheet that small.
    My wife has a cutter that allows her to make darn near anything with it.
    Getting little stuff transferd on perfectly...
  15. Replies
    2
    Views
    1,118

    If you lift all 4 wheels off the ground and lift...

    If you lift all 4 wheels off the ground and lift up your suspension arm, does the wheel turn.

    If you lift all 4 tires off the ground and rev it up like you would to go 30+ MPH does it do anything...
  16. Replies
    9
    Views
    346

    Welcome to the board.. I don't believe Traxxas...

    Welcome to the board..

    I don't believe Traxxas makes an aluminum one. I have seen them from Hot Racing and ST Racing.
    I personally want to try the hot racing one.
  17. Thread: Xmaxx and BEC

    by gunnuts
    Replies
    19
    Views
    1,151

    Yesir! Just have to focus on which RC to work...

    Yesir! Just have to focus on which RC to work on... too many irons in the fire.
  18. Thread: Xmaxx and BEC

    by gunnuts
    Replies
    19
    Views
    1,151

    I have a couple prototypes printed up. I keep...

    I have a couple prototypes printed up.
    I keep screwing up my screw spacing.

    I started off w/ Blender... and I ended up w/ TinkerCad ;)
    If you get into 3D printing Tinkercad is super easy!
    ...
  19. Replies
    21
    Views
    757

    Honestly, if your into this hobby lipo storage...

    Honestly, if your into this hobby lipo storage safety is a thing!
    A good ammo can and some cinder blocks make for a fine storage solution.

    Puffy is one thing... check the resistance! Higher...
  20. Replies
    12
    Views
    2,543

    Verify your gear mesh... I have seen several...

    Verify your gear mesh... I have seen several videos of shaft play in the motors that can allow excessive play in the gears.
  21. Thread: 74 mph run

    by gunnuts
    Replies
    3
    Views
    410

    Wow, I cant believe that didn't blow over.! ...

    Wow, I cant believe that didn't blow over.!
    That looks like an air strip. Great spot!
  22. Replies
    14
    Views
    655

    I am waiting to see what kind of answers you get....

    I am waiting to see what kind of answers you get.
    I just added a HS to my motor because I run a little tall ;)
    I not added fans yet but have been looking around to see what options I can find.
  23. Replies
    60
    Views
    2,068

    Heck Yeah! Welcome back! I was looking at one...

    Heck Yeah! Welcome back!

    I was looking at one of those recently... could not pull the trigger on another nitro.
  24. Replies
    20
    Views
    849

    I hope they keep manufacturing here! I really...

    I hope they keep manufacturing here!
    I really hope they bring back their racing tranny ;)
  25. Replies
    51
    Views
    4,979

    Meh, I was hoping they would come out with...

    Meh, I was hoping they would come out with something for the street.
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4