Search:

Type: Posts; User: NitroBugg

Page 1 of 11 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    252
    Views
    13,558

    Same here...I've gone to our local Hobbytown in...

    Same here...I've gone to our local Hobbytown in Flowood, MS. numerous times and they never have any of the parts I need. They are always out of paint (even the most common colors), poor selection of...
  2. Replies
    21
    Views
    1,965

    They do look nice, but I've never "popped a cap"...

    They do look nice, but I've never "popped a cap" either, so plastic works for me as well.

    On the allow caps...why would you need it to be vented? Kinda defeats the purpose of the bladder? JB...
  3. Replies
    252
    Views
    13,558

    Genuine question...how does an o-ring help?

    Genuine question...how does an o-ring help?
  4. Replies
    14
    Views
    368

    I used Bittydesign...

    I used Bittydesign

    Applied with a small foam brush, and will take 4-5 light coats letting it dry in between coats. Says you can dilute it to use in an air brush. It is water based, but if you let...
  5. Replies
    14
    Views
    368

    You can use liquid mask too. A bit messy, but...

    You can use liquid mask too. A bit messy, but comes off clean.
  6. I agree. The motor is under more load pulling a...

    I agree. The motor is under more load pulling a rig through grass, as the tires will sink down, and the chassis will drag and cause it to heat up quicker. Doing loops or sharp turns in grass will...
  7. Replies
    14
    Views
    648

    I did this mode and works well. Also, using the...

    I did this mode and works well. Also, using the taller shock tower on the front, you "may" want to look into using the 7462X. If I'm wrong, I'm sure someone will correct me.
    ...
  8. You can try moving the servo horn one tooth...

    You can try moving the servo horn one tooth clockwise I think. If its too far to the left, it can hit the chassis when making right turns. Servo endpoints should be adjustable as well.

    I would...
  9. Replies
    13
    Views
    777

    :woot: And did I also mention I run the Mamba X,...

    :woot: And did I also mention I run the Mamba X, and a CC 2400kv 5mm shaft motor? :thumbup:

    Coincidence?
  10. Replies
    6
    Views
    396

    You can always try the "tracks"... ...

    You can always try the "tracks"...

    https://imagizer.imageshack.com/v2/640x480q90/921/BsN2ht.jpg
  11. Replies
    13
    Views
    777

    +3 King Headz is a good motor mount...and...

    +3

    King Headz is a good motor mount...and HR makes a good one as well. The stock Traxxas aluminum motor plate works great with each of those.

    I recommend getting the 30x30x10 Yeah Racing...
  12. Thread: AC charger

    by NitroBugg
    Replies
    9
    Views
    449

    The one Traxxas sells is an AC to DC converter....

    The one Traxxas sells is an AC to DC converter. If you want to go from 110v AC to12v DC, this will work fine.

    However, if you want to go from 12v DC to 110V AC then you'll need to find a Power...
  13. Replies
    6
    Views
    311

    Agree, shrink tubing would be best, but I have...

    Agree, shrink tubing would be best, but I have also used "Liquid Electrical tape" and had good results as well.
  14. Thread: WarBAJR II

    by NitroBugg
    Replies
    698
    Views
    113,034

    LOL...nothing "plain" about that bad boy. Its...

    LOL...nothing "plain" about that bad boy. Its sleek, clean, and incredible looking! :thumbup:

    I like your rear lights much better, but faced with $55.00 vs $8.00, I went with the $8.00 (do plan to...
  15. Replies
    1,123
    Views
    680,256

    Sticky: Added window nets, radiator, rear lights.... ...

    Added window nets, radiator, rear lights....

    https://imagizer.imageshack.com/v2/640x480q90/924/ZEoj3h.jpg
  16. Thread: WarBAJR II

    by NitroBugg
    Replies
    698
    Views
    113,034

    Bored, so I added some rear lights, window nets,...

    Bored, so I added some rear lights, window nets, radiator, and painted the fire extinguisher. Probably lose the rear bumper too. Will keep enough to have a place to secure the sway bar though. Or get...
  17. Replies
    10
    Views
    485

    Not sure whom you're calling "you guys", but I...

    Not sure whom you're calling "you guys", but I never said it was Price Fixing. I said it was a fixed price. (there IS a difference) A part you buy from Traxxas, will be the same price at the other...
  18. Replies
    252
    Views
    13,558

    Never used the castle plugs yet. I know they can...

    Never used the castle plugs yet. I know they can carry a lot of current. I use dean plugs on most of my rigs...but am in the process of switching them out with Genuine XT60 plugs. They are rated...
  19. Replies
    10
    Views
    485

    And any other Traxxas distributor is required to...

    And any other Traxxas distributor is required to sell it at a "fixed" price too, set by Traxxas.

    Only exceptions are a few independent sellers on Amazon, or ebay. And you don't save much in the...
  20. Replies
    2
    Views
    245

    Life battery storage...

    Do Life batteries need to be treated the same as Lipo's when it comes to storage?

    I've heard due to the chemistry of the Life battery, storage charge is not needed. I have also heard a few that...
  21. Replies
    13
    Views
    628

    I agree on the maintenance. Vital to the life of...

    I agree on the maintenance. Vital to the life of the rig. My Platinum is due. No parts needed, just shock and diff fluid change, check bearings, and do a general clean up.

    Like that body as well....
  22. Replies
    607
    Views
    244,517

    Awesome job on the paint!

    Awesome job on the paint!
  23. Replies
    252
    Views
    13,558

    Can't wait to see this rig when you're finished. ...

    Can't wait to see this rig when you're finished. :cool:
  24. Replies
    23
    Views
    796

    All done...and runs Fantastic! A whole pack...

    All done...and runs Fantastic! A whole pack through it without even thinking of getting hot. Running 17\54 and has more speed and torque than I expected. Have a 20T available, but its fast enough as...
  25. Replies
    1,123
    Views
    680,256

    Sticky: Axial Yeti cage mounted on a Slash 4x4 Platinum. ...

    Axial Yeti cage mounted on a Slash 4x4 Platinum.

    https://imagizer.imageshack.com/v2/640x480q90/923/WYO1Bb.jpg
Results 1 to 25 of 252
Page 1 of 11 1 2 3 4