Search:

Type: Posts; User: Phenix2984

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. The Road rage I found (as second hand) are low...

    The Road rage I found (as second hand) are low profile, so it don't works.
    I use Proline F11 3.2" with 17mm hex for these tires.
  2. THANK YOU LizardXO-1! You're a genius, just turn...

    THANK YOU LizardXO-1!
    You're a genius, just turn my brand new HPI Blur (F360C) into Genuine Castle.
    Just one thing: 1st step, downgrade your firmware to the oldest available.
    (The original...
  3. Replies
    34
    Views
    2,210

    On mine, I broke it 2 times: 2 screw on the back...

    On mine, I broke it 2 times: 2 screw on the back side ripped, 1 screw on the top (where you fix the bar) broken.
    Velcro strap fix all my problems.

    I have similar setup (2650kv, 3.2wheel, MIP,...
  4. I use: Front: 30 0000 CST Center: 60 000CST...

    I use:
    Front: 30 0000 CST
    Center: 60 000CST
    Rear: 15 000 CST

    When this #?&?! oil stay in the center diff, it rocks.
    I need a seal solution because the center diff is always empty after 10/15...
  5. Replies
    36
    Views
    1,818

    Same for me before. Reduced by changing the rod...

    Same for me before.
    Reduced by changing the rod ends and ball bearing.
    I think most of the slash have this problem after some times, but nobody drive forward ;)
  6. Replies
    5
    Views
    590

    I've the same problem before! What I did +...

    I've the same problem before!

    What I did + MMM/2650kv/3S battery

    This is the correct conclusion!
    But, the Slash with E-Revo spec and similar motor/ESC is faster even in 3S instead of 4S,...
  7. Replies
    5
    Views
    591

    Strange, mine didn't do that, but I directly use...

    Strange, mine didn't do that, but I directly use FLM diff, I never try it with the stock plastic diff casing.
  8. Replies
    5
    Views
    591

    Hello, For the noise: try to push the car on...

    Hello,

    For the noise: try to push the car on the floor without the motor (or with the motor pinion disconnected), to see if it comes from the car or the motor.
    If it comes from the roller, you...
  9. Replies
    36
    Views
    1,818

    I think too many toe-out angle + to much play in...

    I think too many toe-out angle + to much play in the bellcranck and A-arms.
    As the problem increase when I put bigger wheels, it's logic for me.
  10. Replies
    36
    Views
    1,818

    Exact, I've MMM v3, You can set it with castle...

    Exact, I've MMM v3, You can set it with castle link.
    Most of the servo have more torque when increasing the voltage.
  11. Replies
    36
    Views
    1,818

    I forget and dont find the "edit" button: I...

    I forget and dont find the "edit" button: I increase also the voltage of the servo to 6.0VCC to have more torque on the Sav÷x.
  12. Replies
    36
    Views
    1,818

    I have the same problem after 1 years of...

    I have the same problem after 1 years of continuous use (average of several packs a week):
    https://www.youtube.com/embed/MzlrBfybjUM
    I upgrade:
    - Sav÷x SC-1258 TG (reduce a little)
    - STRC...
  13. Replies
    2
    Views
    1,703

    As I know: - Slash 4x4 front and rear wheels are...

    As I know:
    - Slash 4x4 front and rear wheels are the same.
    - Slash 4x2 rear wheels are the same as Slash 4x4.
    I run with 2x Slash 4x4 wheels and 2x Slash 4x2 rear wheels (the shop where I buy it...
  14. Replies
    15
    Views
    684

    I broke one several month ago. Take a picture,...

    I broke one several month ago.
    Take a picture, send it by email to MIP with description of the problem, they send me a new one free of charge (I live in France and buy it from ebay).
    Very good...
  15. Replies
    35
    Views
    5,752

    Just a very good return about MIP I send them a...

    Just a very good return about MIP
    I send them a message and explanation about my broken part.
    They send me back 2x new parts to replace.
    I highly recommend MIP!
  16. Replies
    35
    Views
    5,752

    From my side, I have some issue with blue loctite...

    From my side, I have some issue with blue loctite on some part (drive shaft, pinion).
    Never have with red loctite.
    For me not a problem to heat the shaft to put off the screw.
    For the part who can...
  17. Thanks a lot!

    Thanks a lot!
  18. Replies
    35
    Views
    5,752

    HA ha you are lucky. I use first blue loctite....

    HA ha you are lucky.
    I use first blue loctite. The screw unscrew itself and drill a little bit the diff ends.
    I use red loctite and it don't moves.
    But after some runs:...
  19. I try Tenshock SC401 (4 Poles) on my stock ESC...

    I try Tenshock SC401 (4 Poles) on my stock ESC and it don't works.
    The results is like "mega cogging".
    I try it with HW 80A ESC and MMM without any troubles.
    When I ask my local store, they says...
  20. Do you have an idea of the offset? It seems to...

    Do you have an idea of the offset?
    It seems to be 2" on the pict (the hex seem to be at the edge of the rim).
  21. Thanks. It seems to have some offset isn't it? ...

    Thanks.
    It seems to have some offset isn't it?


    Did you find it without offset?

    I test with RPM revolver without offset, it fit (very close to the chassis but don't touch at the rear)
    Nearby...
  22. Hello and thanks for the informations, it is...

    Hello and thanks for the informations, it is unbelievably strong. No more hex problem now.
    I did it with Trenchers 2.8" + RPM 3.2" revolver without offset.

    Sorry to re-open the topic, but I need...
  23. Replies
    10
    Views
    2,068

    Hello, I break 3 of them, each times the problem...

    Hello,
    I break 3 of them, each times the problem was the bottom screw who goes out (this screw was always missing after the part break)/
    I recently check after each battery pack and in most of the...
  24. Replies
    16
    Views
    1,007

    Nearby the same setting with 2.8" tires and...

    Nearby the same setting with 2.8" tires and 2650kv 6P motor. (revo slipper/mip drive shaft/tekno rc center drive shaft/17 hex/MMM & 17/52 gearing) I can do wheelings from 0 to 70km/h without any...
  25. Really bulletproof. Just one thing who will help...

    Really bulletproof.
    Just one thing who will help you: use red Thread Lock for the screws, if not you will have some troubles...
    ;)
Results 1 to 25 of 37
Page 1 of 2 1 2