Search:

Type: Posts; User: RedRambler

Search: Search took 0.01 seconds.

  1. Replies
    25
    Views
    789

    I sent an email to HR and they stated...

    I sent an email to HR and they stated “unfortunately we no longer carry traxxas parts”. Unsure if that means for good or what, however is there an alternate option for sway bars?
  2. Replies
    25
    Views
    789

    I couldn’t find a recent thread to jump into...

    I couldn’t find a recent thread to jump into regarding sway bars for the 1/16 slash. I see the hot racing sway bar gets suggested a lot, however it is sold out everywhere I look. Are there...
  3. Replies
    25
    Views
    789

    Yep, I see that now looking on my desktop....

    Yep, I see that now looking on my desktop. Ordered from my phone and didnt realize I could click on the exploded view part numbers. Avid stressed extended shipping times so it might be a few days...
  4. Replies
    25
    Views
    789

    I ordered the Avid Revolution bearings and will...

    I ordered the Avid Revolution bearings and will run the yellow side out towards the dirt. I didnt realize there was such a market for these tiny bearings, but there are a few options..I did use the...
  5. Replies
    25
    Views
    789

    I will be doing some bashing and I am not up to...

    I will be doing some bashing and I am not up to the racing level just yet. I think I might get a couple sets to use grease and oil. Might as well get two and pay shipping once. My LHS doesn’t have a...
  6. Replies
    25
    Views
    789

    Thanks for that info. Going to the LHS at some...

    Thanks for that info. Going to the LHS at some point today to get the new bearings..All the small parts needed add up in cost pretty quick. But you gotta pay to play!
  7. Replies
    25
    Views
    789

    No worries at all, the video was very helpful in...

    No worries at all, the video was very helpful in taking the driveshaft off. I appreciate the visual. I will be going to my LHS in search of bearings. Do the bearings come pre packed with grease or is...
  8. Replies
    25
    Views
    789

    I am thinking about getting all new bearings just...

    I am thinking about getting all new bearings just as preventive maintenance. I will check out the Avid’s. Thanks all for the quick responses.
  9. Replies
    25
    Views
    789

    I am going to have to soak the inner bearing to...

    I am going to have to soak the inner bearing to get it out. The outer bearing was fine, but the inner is almost corroded in, which is obviously the bad bearing.
  10. Replies
    25
    Views
    789

    I got the drive shaft loose and it does not move...

    I got the drive shaft loose and it does not move freely when removed from the rear diff. The driveshaft is almost seized into the bearing. What’s a good approach to get the driveshaft removed from...
  11. Replies
    25
    Views
    789

    Thanks all. I will see what I can get done and...

    Thanks all. I will see what I can get done and report back.
  12. Replies
    25
    Views
    789

    Rear driveshaft issue

    Hello, on my 1/16 slash 4x4 the left rear driveshaft does not spin freely. I ran it yesterday and it ran fine but today only 3 of the driveshafts turn freely. Where should I begin to trouble shoot. I...
  13. Replies
    13
    Views
    597

    Yep, I might just go ahead and do that! Thanks.

    Yep, I might just go ahead and do that! Thanks.
  14. Replies
    13
    Views
    597

    Thanks for the advice, I do appreciate it and...

    Thanks for the advice, I do appreciate it and would rather learn from your mistakes. I won’t be going wider on the wheels. I will look into the kit though. Will that work with a slash 4x4 1/16? Since...
  15. Replies
    13
    Views
    597

    Mine is a 2200 mah 2s. I think I will get the...

    Mine is a 2200 mah 2s. I think I will get the connector to run two lipos parallel before getting a brushless motor. I am not good enough at driving for the current speed levels :lol: I need to do...
  16. Replies
    13
    Views
    597

    Thanks RC Willy. Caleb, that was my next question...

    Thanks RC Willy. Caleb, that was my next question how long I could run the lipo under all out power? Compared to my old nimh, the power is a lot. Rips around like crazy. I can’t imagine it with the...
  17. Replies
    13
    Views
    597

    Thanks Caleb, just the info I was looking for....

    Thanks Caleb, just the info I was looking for. Hooking it up to the charger now. :burnout:



    Thanks Caleb, I will proceed with charging.
  18. Replies
    13
    Views
    597

    New Lipo break in questions

    Hello, new here, and new to Lipo batteries. I just purchased a 2820x for my 1/16 Slash. I have the Traxxas lipo and the Traxxas easy peak plus charger. Is there a break in procedure for the...
Results 1 to 18 of 18