Search:

I have the fd-100 and fd-200. Both excellent dischargers. I also have a couple icharger x6’s. They are capable of discharging but like you said at a very slow pace. And using a charger as a...

It’s for the nitro revo with the aluminum chassis to hold it together.


Sent from my iPhone using Tapatalk

I don’t know what type of mount you have there for the esc but it looks to me like it could be flexing the top of the chassis just enough for the battery door tabs to be at a slight angle, therefore...

I modified the stock receiver box to mount above the chassis brace.
https://uploads.tapatalk-cdn.com/20200923/710dfdc806c8937157c33ab18a811b02.jpg


Sent from my iPhone using Tapatalk
...

https://www.amainhobbies.com/yeah-racing-30x30x10mm-tornado-high-speed-fan-black-yea-ya-0180/p491060


Sent from my iPhone using Tapatalk

No problem. Here is a picture just in case. https://uploads.tapatalk-cdn.com/20200429/9b797334e08cf78b1a53615fb5970084.jpg


Sent from my iPad using Tapatalk

Open up the receiver box and check your wiring. There are two slots for channel 1 (servo) some vehicles use two servos so that’s why there are two. The channel 2 slot is what the speed control should...

I bought these a couple years ago and love them. A little pricy but I was in your situation. I didn’t have the time to build some and these are great quality and really light. Sadly I can’t find any...

https://uploads.tapatalk-cdn.com/20200416/244d57da70c25ee23033da62ce8e8d9b.jpg


Sent from my iPhone using Tapatalk

X4


Sent from my iPhone using Tapatalk

There is a 2mm washer that’s installed under each rear rocker arm post. That gives just enough clearance to work.


Sent from my iPhone using Tapatalk

There is a jig the kit comes with. Just line it up with the corresponding rocker you have and I thread in two screws to hold the jig to the rocker, then use the provided drill bit and drill the hole...

Nothing wrong here. It’s just what Traxxas programed the ESC to do. https://uploads.tapatalk-cdn.com/20200215/85ff443be4dc5f5c8e1d410f5f10858d.jpg
As far as the servo drifting to one side it’s...

I have been using both on my 2.0. No driveline issues. My gearing is 18/50. No temperature problems either. Have a dual fan heat sink on the motor. Trenchers are more all around for example, on-road,...

You could disable it and run it in nimh mode and put low voltage alarms on the batteries. Just when it starts beeping stop driving. Most are customizable from 3.0-3.7v per cell. I would advise no...

These are a little pricy because they are Belted Tired. They look like they should be a great tire. I only have the regular trenchers and they balloon quite a bit. These don’t.
...

What you need to do is calibrate the esc to the new receiver.
Follow the steps below:


Step 1: Start with the transmitter ON, the battery disconnected, and the ESC’s switch in the OFF position...

Did you receive that part I suggested yet? Any updates?


Sent from my iPhone using Tapatalk

I would love to get my hands on some of those LEM o-rings but I can’t seam to find any online [emoji3525] Where did you get yours and how long ago?


Sent from my iPhone using Tapatalk

Yup and it’s nothing to worry about. Sounds like your getting really close. Hope it goes well and lasts a while.


Sent from my iPhone using Tapatalk

The grease from the factory was likely white when it was new. The grease turning blackish grey is normal. It’s from the internal gears wearing ever so slightly. They are black when new and as they...

I use this grease on all of my diffs.
https://shop.advanceautoparts.com/p/lucas-oil-products-x-tra-heavy-duty-grease-145-oz-10301/7070035-P


Sent from my iPhone using Tapatalk

https://uploads.tapatalk-cdn.com/20190908/d46d4c16fb12c4089c1e96e2a8a59fc2.jpg


Sent from my iPhone using Tapatalk

https://uploads.tapatalk-cdn.com/20190908/c2d6e1182412ff124dbb617f9d7f3281.jpg


Sent from my iPhone using Tapatalk

It’s a tight fit. Since it’s a little longer it has the whole width of the bearing on the adapter. The traxxas one only allows for a portion of the bearing to go on.


Sent from my iPhone using...