Search:

Type: Posts; User: TheFirestarter

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    578

    Did you try to buff it out?

    Did you try to buff it out?
  2. Replies
    7
    Views
    976

    Shocks are very easy to get off but take some...

    Shocks are very easy to get off but take some finangling up front. Check out the variable damping kit which allows you to run different rebound and compression. Pick up a couple GTR rebuild kits....
  3. Replies
    6
    Views
    870

    I'm running Pink front Blue rear. VDK all around...

    I'm running Pink front Blue rear. VDK all around on compression #2 front and #3 rear. 50 weight all around. TiN shafts and Jato shaft covers.

    I like my revo low and it handles extremely well....
  4. Replies
    6
    Views
    1,257

    I rotate mine like tires. Back right to front...

    I rotate mine like tires. Back right to front left, front left to back left, back left to front right, and front right to back right. I've completely burned through a set of tires and they are...
  5. Replies
    16
    Views
    905

    What I'm saying is I have the issue on both my...

    What I'm saying is I have the issue on both my traxxas vehicles and both radios. I use an aftermarket rx tx (fs gt5) and use it's tunable gyro which is far beyond what traxxas has. swapping in a new...
  6. I love the nitro revo bodies... but the clipless...

    I love the nitro revo bodies... but the clipless system is so strong and integrates into the chassis to add further protection. Proline also makes bodies that work with the clipless system
  7. Replies
    6
    Views
    404

    as already mentioned, the battery must be...

    as already mentioned, the battery must be unplugged. Traxxas updated the vxl6s to not turn off via the button because people were killing battery packs ~ supposedly
  8. Replies
    7
    Views
    1,136

    It tumbles quite a bit above 30mph, but I think...

    It tumbles quite a bit above 30mph, but I think it was due to mobbing through rock gardens. After swapping the bulk head I realized both pin retainers failed near the skid plate side, but one pin...
  9. Replies
    16
    Views
    905

    nope, my trx6 and erevo 2.0 both have the issue I...

    nope, my trx6 and erevo 2.0 both have the issue I linked in the video... from 1% to 25% it doesn't allow for steering. This is a huge flaw.
  10. My only suspension issue was a hinge pin getting...

    My only suspension issue was a hinge pin getting ripped out of the bulk head. Never broke a rod or rod end, nor an arm.

    The arrma m2c chassis still bend. I've never had an issue with my battery...
  11. Replies
    3
    Views
    266

    I run a flysky gt5 radio. You can change...

    I run a flysky gt5 radio. You can change exponential throttle curves and end points to reduce it. The TQi radio sucks with end points. For steering, it simply stops the servo from moving with the...
  12. Replies
    7
    Views
    1,136

    Bulkhead failure

    I've ordered a new rear bulkhead, 8629, because my suspension arm ripped out the lower left front steel hinge pin. Also ordered the 5321 hinge pins.

    Besides the rear center drive shaft this is the...
  13. Replies
    16
    Views
    905

    My TSM doesn't work when it's set too low. ROFL....

    My TSM doesn't work when it's set too low. ROFL. So I dumped it and run a FlySky GT5 radio. Works a lot better. https://youtu.be/adbp0hvRL9E
  14. Replies
    5
    Views
    713

    It takes a lot to get my Erevo center diff to...

    It takes a lot to get my Erevo center diff to slip. I wouldn't lock it up further. If anything a lighter weight oil should help it turn in some.
  15. You can definitely use the erevo batteries with...

    You can definitely use the erevo batteries with other vehicles. If you want to be a stickler about matching discharge between the packs then just alternate which 3s pack you use.

    You can even run...
  16. What kind of noise? can you post a video or link...

    What kind of noise? can you post a video or link to one? Take the plastic motor cover off, remove the stainless bolt and plastic mesh device from the blue motor plate and rotate the motor away from...
  17. Replies
    2
    Views
    476

    I went with a traxxas 2250 servo as a single...

    I went with a traxxas 2250 servo as a single while waiting for traxxas to replace the broken 2075 units. It ran really hot, but had more than enough torque to overcome the servo saver. Because of it...
  18. Replies
    17
    Views
    835

    KV doesn't = power or torque. KV is the...

    KV doesn't = power or torque. KV is the revolutions per volt unloaded... but more basically a higher kv= lower resistance and a lower kv = higher resistance.

    Same gearing, the higher kv will...
  19. Replies
    17
    Views
    835

    Yeah, the 40 and 42mm motors are all seemingly...

    Yeah, the 40 and 42mm motors are all seemingly 40mm cans with or without fins. I went with a finless 40mm motor because I wanted greater surface area for my heatsink to work, and it has. I'm getting...
  20. Replies
    17
    Views
    835

    Either I had a submission issue or the whole...

    Either I had a submission issue or the whole comment was removed...
  21. I run zip ties from the top of the body mount to...

    I run zip ties from the top of the body mount to the middle support in the rear arms to prevent the suspension from over travel and destroying the shocks and rod ends. All of the rod ends are perfect...
  22. I'm running a single power hobby 35x35x10 fan on...

    I'm running a single power hobby 35x35x10 fan on the same heatsink. It fit s perfectly in the 1st and 3rd set of holes, : :: : arranged like that, where the stock 30x30x10 fans would fit in the 1st...
  23. Replies
    10
    Views
    655

    I've had issues with the traxxas light module on...

    I've had issues with the traxxas light module on my trx6. The junction box won't work unless I keep the lead wire from the truck taped in a certain orientation. Pretty disappointed in its durability,...
  24. Replies
    21
    Views
    998

    You made a factual statement that was incorrect....

    You made a factual statement that was incorrect. What is "proper" heat transfer? The actual keyword is "must," which makes your statement erroneous. By stating you "must" do something, you're...
  25. Replies
    10
    Views
    655

    I hate google drive links. These might work ...

    I hate google drive links. These might work

    https://drive.google.com/file/d/1b8_yxU7bDzXeXQ5Jqt_Qa0-4XqbYkDBF/view?usp=sharing...
Results 1 to 25 of 37
Page 1 of 2 1 2