Search:

Type: Posts; User: dgechrgr469

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. A lot of my cars/trucks are mounted there. The...

    A lot of my cars/trucks are mounted there. The Losi 22SCT and Pro-Line Pro2 chassis both mount them right above the battery in front of the rear tower. I don't think it would be a problem. I use...
  2. Are you running extra stuff through your...

    Are you running extra stuff through your receiver? Fans, lights or anything else that could be drawing more current than it's designed for?

    Sent from my moto g stylus using Tapatalk
  3. I have made a shelf the size of the esc or a...

    I have made a shelf the size of the esc or a little bigger and attached it under the two screws on the front of the rear shock tower. Sometimes depending on space limitations I'll also have extra...
  4. Replies
    15
    Views
    729

    Yeah, sometimes those adapters add some crazy...

    Yeah, sometimes those adapters add some crazy offset to the wheels. I didn't check my 14mm adapters to see but I think they were made for the "monster" truck look.

    Sent from my moto g stylus using...
  5. You're not going to be able to check the slipper...

    You're not going to be able to check the slipper unless you test it in under a load. Most recommend tightening it fully then backing out 1/4 to 1/2 of a turn as a good starting point.

    Sent from my...
  6. Replies
    15
    Views
    305

    From my measurements I guess I'll change those...

    From my measurements I guess I'll change those rear RPM arms to the ProTracs and gain a little more width. The RPM arms must be the stock width.

    Sent from my moto g stylus using Tapatalk
  7. Replies
    6
    Views
    201

    I have always had trouble changing programming...

    I have always had trouble changing programming settings or calibrating throttle settings with anything less than a fully charged battery.

    Sent from my moto g stylus using Tapatalk
  8. Replies
    34
    Views
    712

    I measured my Revo/Slayer shocks, 87mm extended,...

    I measured my Revo/Slayer shocks, 87mm extended, 70.5mm compressed, no bumper. These are center to center measurements.

    Sent from my moto g stylus using Tapatalk
  9. Replies
    15
    Views
    305

    Ok, here's what I've got. They are RPM Rustler...

    Ok, here's what I've got. They are RPM Rustler arms measured center to center on the pins, front 100mm, rear 92mm. The fronts are what they call extra wide. Part #'s are black 70662, green 70664,...
  10. Replies
    15
    Views
    305

    I've got some spare 2wd ProTrac arms I'll measure...

    I've got some spare 2wd ProTrac arms I'll measure and see how they compare.

    Sent from my moto g stylus using Tapatalk
  11. Replies
    15
    Views
    305

    Unfortunately I'm working today and can't...

    Unfortunately I'm working today and can't remember what arms I used on this crawler tired 2wd Slash bug I built. I'll check my build notes tonight.

    Sent from my moto g stylus using Tapatalk
  12. Replies
    15
    Views
    305

    Aren't the Stampede arms wider than...

    Aren't the Stampede arms wider than Slash/Rustler?


    Sent from my moto g stylus using Tapatalk
  13. Replies
    8
    Views
    224

    I like mine, it charges fast too. Sent from my...

    I like mine, it charges fast too.

    Sent from my moto g stylus using Tapatalk
  14. Replies
    11
    Views
    357

    Yes, I have done it in the past. I use Pro-Line...

    Yes, I have done it in the past. I use Pro-Line transmissions mostly now.

    Sent from my moto g stylus using Tapatalk
  15. Replies
    11
    Views
    357

    It will make it easier although it is possible it...

    It will make it easier although it is possible it could drop in place too depending on manufacturing tolerances.

    Sent from my moto g stylus using Tapatalk
  16. Replies
    11
    Views
    357

    Heating the gear will make it expand, it should...

    Heating the gear will make it expand, it should make it easier to drive it onto the shaft than if they are both room temperature. You can try freezing the shaft (it will contract) but it's hard to...
  17. Replies
    8
    Views
    434

    Misread your post, it's at the max, will it...

    Misread your post, it's at the max, will it change if you try a different battery or do you only have the one?

    Sent from my moto g stylus using Tapatalk
  18. Replies
    8
    Views
    434

    Sometimes there is a maximum it will let you...

    Sometimes there is a maximum it will let you charge even though it can go higher depending on the battery.

    Sent from my moto g stylus using Tapatalk
  19. Replies
    8
    Views
    434

    I bought a 4s battery recently that I had to...

    I bought a 4s battery recently that I had to cycle through many balance charges and storage charges to bring one cells voltage up to match the other 3, it was so low my traxxas charger didn't want to...
  20. Replies
    11
    Views
    357

    Heat the gear with a lighter, the best lighter to...

    Heat the gear with a lighter, the best lighter to use is a butane log/grill lighter. Then drop it on quickly.

    Sent from my moto g stylus using Tapatalk
  21. Replies
    8
    Views
    434

    A low voltage alarm/monitor/checker like the...

    A low voltage alarm/monitor/checker like the Venom 0644 would be a inexpensive way to check the voltage of the pack and individual cells.

    Sent from my moto g stylus using Tapatalk
  22. Replies
    30
    Views
    1,249

    I'll jump in and say the shorter tower and the 4...

    I'll jump in and say the shorter tower and the 4 tec shocks would work fine, the biggest reason for something like that would be a lighter car. There isn't a whole lot of suspension travel for a drag...
  23. Replies
    30
    Views
    1,249

    I agree, my fastest car uses two batteries in...

    I agree, my fastest car uses two batteries in parallel for extra weight and the extra power. I was getting tire shake with my car being lighter without foam in the tires.

    Sent from my moto g...
  24. Replies
    30
    Views
    1,249

    The Dremel works but can be messy with the dust....

    The Dremel works but can be messy with the dust. I'm thinking of getting a scroll saw, it sure beats 7 grand for a water jet.

    Sent from my moto g stylus using Tapatalk
  25. Replies
    341
    Views
    81,165

    They are aluminum, I believe where the "u joints"...

    They are aluminum, I believe where the "u joints" are assembled with the pins are steel. I've bought the cheaper axles up to this point. Just ordered a set of the $40 axles because that's all that...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4