Search:

Type: Posts; User: Jeff Wohlt

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    689

    I always use a good grease but the key is a few...

    I always use a good grease but the key is a few drops of any oil down it as well. Makes for a slather that is very fast...do not forget the prop shaft too.
  2. Replies
    17
    Views
    3,961

    Best upgrade is a 4082 1600 KV with 6S and...

    Best upgrade is a 4082 1600 KV with 6S and propping with a bigger prop. Good runtime and easy on ESC and cells. I would get the 180 ESC or similar. Makes for a long run time and in 60mph range. Props...
  3. Replies
    21
    Views
    10,304

    There are several props out there that work well....

    There are several props out there that work well. Just so you know I am the one that sells most of these upgrades for the shafts. "rcraceboat" I turn the 5mm to 3/16" so they fit the better props and...
  4. Replies
    12
    Views
    522

    For the last several years I have run fast...

    For the last several years I have run fast electric boats. Here is the stuff that works well. Soak your servos down with it and radio and all. Some actually left the stuff in the servo...others...
  5. Replies
    9
    Views
    365

    Excellent, Oval. I appreciate it. I just did not...

    Excellent, Oval. I appreciate it. I just did not want to hurt this thing since it is doing so well for me.

    Guess I did well getting over a gallon of fuel through it without plug problems...it...
  6. Replies
    9
    Views
    365

    Can a person even buy the stock plug that comes...

    Can a person even buy the stock plug that comes in it...and what is it?

    So anyone else running the 3230? Is the 3230 a long plug and the stock one a short plug or what?

    Thanks,
  7. Replies
    9
    Views
    365

    Glow Plug Choices?

    Nobody seems to carry (back ordered) the 3231 plug.

    I found the 3230 and it says is a hotter plug than the 3231 and more perfromance. I did not know what to do...so I bought a couple.

    Will they...
  8. Replies
    7
    Views
    252

    And you can, in short time, cook an ESC or cells....

    And you can, in short time, cook an ESC or cells.

    You can run them down like this but sounds like you are talking about totally discharging them...which at that point you need a small bulb for...
  9. Replies
    8
    Views
    334

    I also agree with the K&N...good stuff and in a...

    I also agree with the K&N...good stuff and in a spray can. A bit high but a can lasted me for years and years on a reg. auto filter.
  10. Replies
    2
    Views
    294

    Hey thanks...I guess I just need to do more of a...

    Hey thanks...I guess I just need to do more of a rinse than leaving it in there...some will stay no matter what. The book does not say...drain the excess out but I guess they think it will come out...
  11. Replies
    9
    Views
    417

    I always put my rec. in a balloon. Use...

    I always put my rec. in a balloon.

    Use Areotrneds aeroplate and spray in your servos and rec. It works. You can get it at rummrunnerracing.com or go to the Aerotrend website.
  12. Replies
    7
    Views
    252

    RC-Dude...that is about the worse thing you can...

    RC-Dude...that is about the worse thing you can do if the boat is still in the water...the amps and heat is a killer after you top charge goes down...that is when you should get it off the water...
  13. Replies
    7
    Views
    252

    Go to the store and buy you 8-10 #1157 auto...

    Go to the store and buy you 8-10 #1157 auto bulbs.

    Solder a wire (I used some stripped copper from home wiring) and solder this down the side (-) and then one across the bottom contacts (+) then...
  14. Replies
    22
    Views
    3,144

    For water you need to spray your inside of servos...

    For water you need to spray your inside of servos and ESC and radio with Aerotrend...it keep moisture out and works well.
  15. Replies
    22
    Views
    3,144

    These boats race in an oval...the reason they are...

    These boats race in an oval...the reason they are built for one way turns. Models turn right for racing but the real ones go left. Miss Bud comes to our lake every summer to sert records. In...
  16. Replies
    10
    Views
    325

    Link, please.

    Can someone get me a link to dynamite?
  17. Replies
    2
    Views
    294

    WD-40 Vapor locks

    I just wondered if anyone else had problems with the motor not turning over after WD-40 is put in. I usually put it in the carb and plug hole...just a couple short blasts and then I leave it.
    ...
  18. Replies
    6
    Views
    313

    Bringing back to the top. I need more info on the...

    Bringing back to the top. I need more info on the LSN. Mine is set in the middle of the slit...do I go lean or rich?
  19. Replies
    6
    Views
    313

    Mine was set where it is in the middle...in other...

    Mine was set where it is in the middle...in other words...the slit goes against the arm and not in-line. I think it is rich as well so I guess I will lean it an line it up. I did the pinch test but...
  20. Replies
    14
    Views
    557

    Tower sells those bearings...4X8 they mostly fit...

    Tower sells those bearings...4X8 they mostly fit in the ABC boats and even some other Kyosho, etc. Mainly because the use 4mm shafts. I also use loctite on most all my screws and set screws. Never...
  21. Replies
    14
    Views
    557

    They can come off but it is when you shut down...

    They can come off but it is when you shut down after running hard it can be pulled off from the force and no foward thrust.

    Alot of guys only use fuel tubing slid over the shaft.

    I would never...
  22. Replies
    5
    Views
    203

    3m #270 is a sealer that one ESC builder uses...

    3m #270 is a sealer that one ESC builder uses (RC-Hydros) which is the best out there anyway.

    You can also use it on the radio but not on the freq chip.
  23. Replies
    14
    Views
    557

    Octura props are (4 series = 1.4 pitch) and (6...

    Octura props are (4 series = 1.4 pitch) and (6 series has 1.6 pitch)
  24. Replies
    6
    Views
    472

    Missouri????...me too! I live in Jefferson...

    Missouri????...me too!

    I live in Jefferson City. Had a T-mAxx for about a month now.

    I ran mine yesterday in same weather...really did not need to be richened at all.

    It takes mine awhile...
  25. Replies
    3
    Views
    275

    Thanks...still got smoke so I'm good. Just...

    Thanks...still got smoke so I'm good. Just wondering if people were going as much as 3 turns or anything.
Results 1 to 25 of 48
Page 1 of 2 1 2