Search:

Type: Posts; User: TruckerTucker

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. But seriously, guys! What advancements do you...

    But seriously, guys! What advancements do you want to see? A 4.3? A 3 speed? A 100+ mph 5 tec? Those are jokes �� but what do you want to see?
  2. Replies
    1
    Views
    52

    I think you would have clearance from the...

    I think you would have clearance from the spoiler, right? If it fits, Why not? I'd put a 17-19 tooth pinion on tho to protect your titan for bashing, maybe try 23-25 for onroad speed runs.
  3. Replies
    1
    Views
    21

    Pro 15 carb ?'s

    So I have a few 15 carb ?'s. I stall my engine every time I accelerate at full throttle, after replacing the crankcase on my engine. I figured, well, I ought to re tune. So I figured I'd set...
  4. Replies
    3
    Views
    89

    Did you just get a new Sport or just a new engine?

    Did you just get a new Sport or just a new engine?
  5. Replies
    7
    Views
    89

    +1 to that. I run 2 1800 mAh 7.2v AA nicad packs...

    +1 to that. I run 2 1800 mAh 7.2v AA nicad packs in parallel tied to each other. Weighs it down better. Had to move some stuff to get it to fit however. Gives me good runtime.
  6. Replies
    8
    Views
    349

    They already went out once. Hobby shop was out of...

    They already went out once. Hobby shop was out of stock of aluminum unfortunately, so I went plastic.
  7. Replies
    20
    Views
    242

    Just adjust where your servo saver is sitting....

    Just adjust where your servo saver is sitting. Unscrew it and move it a little left or right, then screw it back down.
  8. Replies
    8
    Views
    173

    Dang, that puppy be looking good!

    Dang, that puppy be looking good!
  9. I am actually looking to get new bearings for the...

    I am actually looking to get new bearings for the ol Pro 15. I took them out yesterday and they were a little shabby. Are Boca by best bet there? I also saw Fast Eddy but those looked a little cheap.
  10. Replies
    7
    Views
    89

    You either have to put in a 7.2 volt nihm/nicad,...

    You either have to put in a 7.2 volt nihm/nicad, or a 7.4 volt 2s lipo. 8.4 volts is too much for the Marine ESC to handle. But yes you can run a 7.2 or 7.4 volt battery in any Traxxas model, but it...
  11. Replies
    27
    Views
    339

    Traxxassaxxart, people love to complain....

    Traxxassaxxart, people love to complain. Annocondas are fine tires. I've used them for 6 years and never had issues. If you want an on road only tire, they are your best bet Traxxas wise.
  12. Replies
    36
    Views
    3,433

    Oh man you should put a 3.3 engine in it. You...

    Oh man you should put a 3.3 engine in it. You will be happily surprised if you put in the time to learn with Nitro. It is very rewarding and powerful, it gets attention, and it would be something...
  13. Replies
    7
    Views
    193

    I'm about to replace the worn bearings on my pro...

    I'm about to replace the worn bearings on my pro 15. Is it really that hard to get them in and out? I got them out rather easily.
  14. Replies
    7
    Views
    89

    It will rust everything if you don't take care of...

    It will rust everything if you don't take care of it, once you are done running it in salt water, rinse it off with clean water and use a water repelling product such as WD-40 to prevent rust.
  15. Replies
    5
    Views
    64

    You have to have a picture hosting site such as...

    You have to have a picture hosting site such as Image Shack, you cannot directly upload images just FYI, in case you didn't already know. Welcome to the Forums!
    -TT
    Also, that signature :thumbdown:...
  16. Replies
    11
    Views
    352

    I mean anytime you have more wear and play, it...

    I mean anytime you have more wear and play, it causes inefficient and slower running, which prompts you to pull the trigger harder which prompts the motors to wear out. Ball bearings will definitely...
  17. Accidental post

    Accidental post
  18. Hey man you know it the arrma people can be a...

    Hey man you know it the arrma people can be a little bit weird sometimes. And Kevin Talbot stands for the normal bashers out there who just drive there RC car like normal people. Traxxas is the brand...
  19. Replies
    7
    Views
    8,046

    Hey, take your time! I'm just glad you haven't...

    Hey, take your time! I'm just glad you haven't given up on it!
  20. I feel like this is irrelevant 1. Because no one...

    I feel like this is irrelevant
    1. Because no one will ever bash their car that hard
    2. You can't spell X Maxx
    3. Literally no one is bashing arrma. Mike said he personally didn't own one or care...
  21. Replies
    7
    Views
    257

    Yes, my moral dillema has been finding the rims...

    Yes, my moral dillema has been finding the rims (wheels) and tires that are the same width, I'll take a look at proline.
  22. Replies
    7
    Views
    8,046

    Did you ever get on with this project? You know...

    Did you ever get on with this project? You know all of Traxxas Forums wants to see you put a brand new pro .15 marine in that puppy and post a video. Traxxas still sells the Marine engine new!
    At...
  23. Replies
    7
    Views
    257

    Yep. Rims are the hardest to get. It's bad enough...

    Yep. Rims are the hardest to get. It's bad enough getting 2.8" rims with no hex or stub axle pin slots, now I have to find 2.2" stadium style rims with 5/11/4 bearing slots! What a convoluted design!...
  24. Replies
    16
    Views
    472

    My pro 15 or vxls haven't shredded thru the super...

    My pro 15 or vxls haven't shredded thru the super glue yet haha. Maybe I'm just a more conservative driver. I mean, I have a Rustler running Stinger 20t, 16/90 designated wheelie truck and even that...
  25. Also, ran my rustler vxl 31/76 on 3s too and...

    Also, ran my rustler vxl 31/76 on 3s too and never overheated, even mowing through grass and off road. Lol.

    -Mike
    Quote didn't work. Hmm. Well, welcome to the 31/76 club!
Results 1 to 25 of 103
Page 1 of 5 1 2 3 4