Search:

Type: Posts; User: zedorda

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    8
    Views
    73

    I have not been using her much since I been...

    I have not been using her much since I been trying to find a good 3s battery so please excuse the dust but this is the setup I use. I offered it just for comparison sake. I have the single piece...
  2. Thread: Axles

    by zedorda
    Replies
    12
    Views
    342

    As it is true you can destroy any axle with abuse...

    As it is true you can destroy any axle with abuse the stock Rustler 4x4/extreme duty axles can handle 3s use quiet well. But if you want to go all out Kevin Talbot on your rig mip might be your only...
  3. For most people these adapters will work fine but...

    For most people these adapters will work fine but understand they will make any settings for "timing" inaccurate if you use them.
  4. I have actually given this some thought and have...

    I have actually given this some thought and have talked to a few manufactures of the fluids used. I change my diff fluid every 120-150 hours of use or every 4-6 months of mixed use/storage. For most...
  5. Replies
    5
    Views
    535

    This is my Slash Monster Truck with an E-Maxx...

    This is my Slash Monster Truck with an E-Maxx body, HR 17mm hubs /w 6mm offset. On Pro-Line 2.8 Trenchers.

    http://u.cubeupload.com/zedorda/IMG20190221224306717.jpg...
  6. Replies
    14
    Views
    262

    I see you don't understand what I am talking...

    I see you don't understand what I am talking about. And I am sick of teaching the same stuff over and over. Learn what servo resolution is and you might get it.
  7. Replies
    12
    Views
    337

    My real point was that for a 1/16th rig a smooth...

    My real point was that for a 1/16th rig a smooth brushless system wouldn't be cheap. The stock brushed motor is pretty fast already and would be smooth at low speed on the cheap.
  8. Replies
    14
    Views
    262

    Please explain why a higher resolution servo...

    Please explain why a higher resolution servo wouldn't fix the problem? How would you make smaller adjustments with a servo without the ability to do so? Since that directly requires a higher...
  9. Replies
    12
    Views
    337

    That is because cogging is less the heavier the...

    That is because cogging is less the heavier the rig and those 2 are much heavier than a 1/16th rig. Plus cogging in a sensored system is more about the ESC than the motor and I bet you don't have a...
  10. Replies
    13
    Views
    343

    Boil them. ...

    Boil them.

    https://www.youtube.com/watch?v=s2cHyYFX3w0
  11. Replies
    3
    Views
    190

    This can be a nice tool:...

    This can be a nice tool: https://scriptasylum.com/rc_speed/top_speed.html
  12. Replies
    12
    Views
    337

    FYI there is nothing special or different between...

    FYI there is nothing special or different between a motor labeled for racing or crawling or not. They are marketing terms and not a technical description. If you know what Kv you want ignore the...
  13. Replies
    14
    Views
    262

    Expo on the Tx is for high resolution servos. And...

    Expo on the Tx is for high resolution servos. And it would fix the problem if the servo had the ability to move the way the Tx is wanting it to. The OP has become good enough of a driver to see and...
  14. Replies
    8
    Views
    286

    Yeah racing fans are some of the best but can be...

    Yeah racing fans are some of the best but can be pretty loud if that even matters.
  15. Replies
    14
    Views
    491

    I so agree. When I started my Monster Slash I...

    I so agree. When I started my Monster Slash I thought there had to be an open wheel body category for aftermarket Slash bodies and was shocked to see the lack of any commonly used ones.

    I didn't...
  16. Replies
    14
    Views
    262

    Nothing in the transmitter with increase the...

    Nothing in the transmitter with increase the resolution of the servo. The resolution of the servo determines the gap between the gates. The gates are the number of positions in the 360 degrees of...
  17. Same setup I went with on my Monster Slash 4x4....

    Same setup I went with on my Monster Slash 4x4. It made suspension setup much easier.
  18. Volt up and gear down make for better RCing days.

    Volt up and gear down make for better RCing days.
  19. Replies
    14
    Views
    491

    For me that was the stock long version E-Maxx...

    For me that was the stock long version E-Maxx body. What I noticed is most of the aftermarket E-Maxx bodies are much larger than the plain stock one. I have a thread here with pictures but here are...
  20. The wobble is from a misaligned alignment likely...

    The wobble is from a misaligned alignment likely from the crash. It is "normal" in the sense that most people don't know what it is from so they can't fix it so you see it a lot. But is not normal in...
  21. Replies
    2
    Views
    215

    I am pretty sure most of the 1/10 rally are 4x4...

    I am pretty sure most of the 1/10 rally are 4x4 so if going with a castle motor I wouldn't go smaller than the 1410 can with a kv somewhere between 3400-4600. Outside of that range you might have...
  22. Replies
    5
    Views
    212

    I have used shoe goo and zip ties in interesting...

    I have used shoe goo and zip ties in interesting ways to mount stuff.
  23. Thread: Merv Built!

    by zedorda
    Replies
    6
    Views
    449

    The body is not a protective barrier. One hard...

    The body is not a protective barrier. One hard hit to the roof can destroy a motor can. I already had it happen. I now have a heatsink snapped on to motor just to take the hit next time. But good...
  24. Replies
    10
    Views
    532

    I find it funny how so many people equate 3s to...

    I find it funny how so many people equate 3s to breaking things but love to leave out how the lack of throttle control is the real reason. Because I have put a 3s in every RC I have and not one has...
  25. Replies
    14
    Views
    1,204

    I have been using the metal posts on my sons...

    I have been using the metal posts on my sons Stampede for over a year now and my solution was these below the body.

    http://u.cubeupload.com/zedorda/IMG20200403133237980.jpg
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4