Search:

Very nice,super clean build

Sent from my SM-G973W using Tapatalk

Just to be clear, The Vaseline is for the rx box seals.all it takes is one wire twisted and it can leak a bit.Its more of a preventative measure.

Sent from my SM-G973W using Tapatalk

A $5 low voltage alarm will solve the no lvc issue.
Its at least 2nd gen as its 2.4 ghz.
Mine was original am 27 mhz.
The body color scheme changed and radio changed,esc got a update thats about...

Make sure your rx box is sealed good.
I use a little Vaseline on the o ring and seals to try and stop moisture getting in.
The fresh water itself is not the issue its whats in the water once you...

If it is equipped it should have a small light on it.Like this,mine was not equipped.
Thats why the sticker is missinghttps://uploads.tapatalk-cdn.com/20201221/b7ba6a67d591fe40580dc0637754fb95.jpg...

Are you sure you are 15?
You are more articulate and well spoken than the majority of adults i have dealt with over the course of 50 years.You seem to have a good head on your shoulders,but more...

This is pretty much exactly what I would have suggested.avoid hi gear when the diffs are locked on surfaces that have good traction like pavement

Sent from my SM-G973W using Tapatalk

Make sure your trims on the radio are at zero before calibration if they are not already.



Sent from my SM-G973W using Tapatalk

I like it.looks good

Sent from my SM-G973W using Tapatalk

I am in agreement with you.
unsprung weight is what I aim for

Sent from my SM-G973W using Tapatalk

No, won't hurt anything.

Sent from my SM-G973W using Tapatalk

Xt 60 on most rigs I have .
Depending on what your running in your summit you may want bigger but I don't see the need.i ran 4s on a tekin rx8 2200 kv setup on the old connecters no issue.

...

I personally like the xt series of connecters.

Sent from my SM-G973W using Tapatalk

In reality driving time is the best teacher.
learning line choice and tire placement can be different from rig to rig so practice is the best..find a practice line to run,So when you make a change...

Just the hard body shell is what they want

Sent from my SM-G973W using Tapatalk

You pull only signal from the rx.
Power direct from the bec.
There is a pre-made harness available

Sent from my SM-G973W using Tapatalk

I run the 10amp castle as the 2.0 was not made at the time

Sent from my SM-G973W using Tapatalk

I run a bec on all my rigs. more for clean power and available amps when needed.also to run at 7.4 to feed a servo

Sent from my SM-G973W using Tapatalk

Don't over volt the rx or the micro servos they can't handle it.


Sent from my SM-G973W using Tapatalk

Those are for optinal sensors.voltage temp and rpm more important on go fast cars than us slow pokes.lol

Sent from my SM-G973W using Tapatalk

Ch 1 steering
Ch 2 esc
Ch 3 hi/low
Ch 4 diff lock usually front.
Ch 5 rear diff.
This rx has 2 ch 1's only need one for this truck.
steering in
either of the ch 1's.
Yes red...

Looking good

Sent from my SM-G973W using Tapatalk

The 57 on the shelf looks pretty cool too

Sent from my SM-G973W using Tapatalk

Looks pretty solid.nice work, man 3d printing is a game changer now all you need is a idea and a need for something particular.
Mine was just some bent up scrap step flashing metal I had laying...

Mine is a little worse for wear took the quick way down a cliff,it happens..lol
A nice solid mount would be good.


Sent from my SM-G973W using Tapatalk...