Search:

Type: Posts; User: Rico116

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Hey that's why you ask questions now you know....

    Hey that's why you ask questions now you know. Better to know than not know at least something. Knowing a little bit is a starting point. I check things like every 10-15 minutes make sure everything...
  2. What do you mean how do you run something off the...

    What do you mean how do you run something off the battery? I know you could run stuff off the receiver. I haven't seen any fans that are 12 volt as the speed control regulates everything. But someone...
  3. There isnt no stupid question around here. When I...

    There isnt no stupid question around here. When I use fans it does keep the motor alot cooler. I also feel like the run times do extend a bit. I also feel like if the motor isn't running so hot helps...
  4. You could see the fans are suppose to be even,...

    You could see the fans are suppose to be even, touching each other but right now it is sitting on 2 washers most likely from impacts.
    Edit I could actually see in the picture the right fan casing is...
  5. They sound like they perform pretty decent as...

    They sound like they perform pretty decent as long as you don't take it bashing I land on my back a lot still a beginner driver lol. I also think the spacers could contribute too failure of a fan...
  6. Thanks for the suggestion I actually saw you...

    Thanks for the suggestion I actually saw you mention about r1 fans on another post while Googling. I can't handle plastic I always smash the casing at least on the yeah racing fan how has the r1 fans...
  7. Protek Fan fitment on yeah racing heatsink or other possible fans that do fit

    How's everyone doing?

    Looking for a new fan to try out on my yeah racing heatsink that is currently installed on my motor. I don't want yeah racing fans anymore because the fans have gave me...
  8. Replies
    10
    Views
    303

    I have the same lights Acidic recommend the ebay...

    I have the same lights Acidic recommend the ebay one the lights are bright you could see it way down the street. I don't have a video of it going down the street but they are pretty nice. As for the...
  9. Replies
    21
    Views
    548

    Alot of food for thought, thanks everyone for the...

    Alot of food for thought, thanks everyone for the answers.

    Sent from my SM-A716U using Tapatalk
  10. Replies
    21
    Views
    548

    Thanks, Good to know always heard of thermal...

    Thanks, Good to know always heard of thermal paste but wasn't sure about it.

    Sent from my SM-A716U using Tapatalk
  11. Replies
    21
    Views
    548

    Motor cooling and surrounding areas

    Hows everyone doing?
    I'm looking at upgrades anybody have any experience with these how would the motor plate and motor mount assist with cooling of the motor and everything else? waist of money or...
  12. Replies
    8
    Views
    420

    Makes sense. I was thinking since the teeth are...

    Makes sense. I was thinking since the teeth are almost gone. The force of the bellcrank turning causes the servo horn to skip teeth and the servo horn cannot return to the original position as it...
  13. Replies
    8
    Views
    420

    Steps I took 1) readjusted the steering linkage...

    Steps I took
    1) readjusted the steering linkage to 31.8mm according to traxxas manual
    2) Adjusted everything according to manual even the 7 degrees offset towards rear
    3) Inspected my servo gears...
  14. Replies
    8
    Views
    420

    Yes very correct good point made. Sent from my...

    Yes very correct good point made.

    Sent from my SM-A716U using Tapatalk
  15. Replies
    8
    Views
    420

    Just checked the manual gonna try this and let...

    Just checked the manual gonna try this and let you know... I was wrong the whole time with aligning the servo. I should really start reading manuals, LOL


    Sent from my SM-A716U using Tapatalk
  16. Replies
    8
    Views
    420

    Thanks, The screw issue has been fixed. I was...

    Thanks, The screw issue has been fixed. I was testing a aluminum horn because the plastic horn kept stripping. The screw was scraping on the chassis.

    The hum/buzz is when the wheels are elevated...
  17. Replies
    8
    Views
    420

    Servo saver shot?

    Hows everyone doing?

    I think my hd servo saver spring may be bad. I have had the spring since mid June.

    When just the servo is connected operation looks to be fine. Video is linked below Link 1...
  18. Replies
    8
    Views
    377

    Everything is connected to the receiver the...

    Everything is connected to the receiver the lights all 5 channels are full. I just don't understand the plastic fans never gave me issues till I upgraded to aluminum yr fans. I'm thinking it might be...
  19. Replies
    8
    Views
    377

    Thanks, I have it hooked up to my receiver as...

    Thanks, I have it hooked up to my receiver as well.

    Sent from my SM-A716U using Tapatalk
  20. Replies
    8
    Views
    377

    Thanks, may be a good option Sent from my...

    Thanks, may be a good option

    Sent from my SM-A716U using Tapatalk
  21. Replies
    8
    Views
    377

    Accessories not working

    How's everyone doing?
    My first run after getting a replacement esc from Traxxas the truck is fixed now.
    But before the replacement esc I had two yeah racing fans and the heatsink at first starting...
  22. Replies
    5
    Views
    394

    I would say check your batteries in your...

    I would say check your batteries in your controller my controller started blinking red red, but I dont remember if the speed control was blinking green too. If your batteries are even a bit low the...
  23. Replies
    5
    Views
    210

    I dont have the tires but is should fit according...

    I dont have the tires but is should fit according to amain description...
  24. Replies
    5
    Views
    210

    Thanks, I didn't know there was adapters for...

    Thanks, I didn't know there was adapters for conversion so in theory you could possibly fit 3.8's on a slash with a hex adapter. That's just me assuming, but will have need a bigger motor but have to...
  25. Replies
    5
    Views
    210

    Proline Trencher , Wheels only

    Hows everybody doing ?
    I'm looking for the wheels only not the tires so I can glue it myself but I can't seem to find them I been searching, anybody know if you could just get the 8x32 to 17mm...
Results 1 to 25 of 236
Page 1 of 10 1 2 3 4