Search:

Type: Posts; User: jimbo74

Page 1 of 20 1 2 3 4

Search: Search took 0.28 seconds.

  1. Thread: 4wd to 2wd

    by jimbo74
    Replies
    6
    Views
    157

    eh, running it in 2wd is going to make it handle...

    eh, running it in 2wd is going to make it handle like crap..... if you want a 2wd slash, get a 2wd slash.... I have a 2wd slash, and a 4wd slash, and have run the 4wd as a 2wd and it sucked.
  2. Replies
    8
    Views
    192

    Jst plug Just standard tamiya

    Jst plug

    Just standard tamiya
  3. Replies
    11
    Views
    338

    And then the axle shafts, and then...... leave it...

    And then the axle shafts, and then...... leave it 2s, for real.... otherwise you will end up with a $1500 slash....

    Ask me how I know
  4. Replies
    13
    Views
    266

    velcro strap

    velcro strap
  5. Replies
    13
    Views
    266

    Smc is the best value. There are some other...

    Smc is the best value.

    There are some other brands that are ok as well.

    I would not get a huge battery, more runtime also means more weight, and more heat build up. It osn't a 1 and dome...
  6. Replies
    13
    Views
    266

    depends what you are looking for SMC are...

    depends what you are looking for

    SMC are awesome for the value
  7. Replies
    3
    Views
    209

    sounds like you have a short somewhere. either...

    sounds like you have a short somewhere. either connected improperly, or the motor fried when you fried your esc
  8. Replies
    7
    Views
    239

    Only the aluminum allows for the more toe angle...

    Only the aluminum allows for the more toe angle is installed. Swapping them left on right and right on left makes them closer to 0 toe. It helps with stability though. And since you aren't going fast...
  9. Replies
    13
    Views
    465

    Also, the center diff is not to be used with...

    Also, the center diff is not to be used with larger cell count batteries. Just asking to fry it....
  10. Replies
    13
    Views
    465

    If it is stock, you have a slipper clutch. If...

    If it is stock, you have a slipper clutch.

    If you want a slipper or a center diff, depends on what your use of the vehicle is. I prefer a slipper clutch in all my vehicles.
  11. Replies
    1
    Views
    219

    Your wheels are bent and tires unbalanced. Every...

    Your wheels are bent and tires unbalanced. Every set of wheels I put on bend. I drive like a maniac.

    Aluminum carriers will be better than plastic.
  12. Replies
    3
    Views
    180

    If the bearings are not the same on both sides,...

    If the bearings are not the same on both sides, then yes, it can be important.
  13. Thread: Help!!

    by jimbo74
    Replies
    11
    Views
    335

    Did you change the pinion? 3s pits more strain...

    Did you change the pinion? 3s pits more strain and heat. The fact it was in snow doesn't mean it didn't overheat
  14. Replies
    4
    Views
    267

    15k is pretty thin. If yours is tight, you may...

    15k is pretty thin.

    If yours is tight, you may have over torqued the cup
  15. Replies
    5
    Views
    341

    screws loosen, especially on parts that are...

    screws loosen, especially on parts that are subject to using the screw as a hinge
  16. Replies
    3
    Views
    253

    Over thinking it. Put it on, put wheel on,...

    Over thinking it. Put it on, put wheel on, tighten nut
  17. Replies
    18
    Views
    831

    You can do whatever you want, but just doing one...

    You can do whatever you want, but just doing one side is going to be weird... I get the idea like a nascar, but those use different sized tires too...

    Those spacers will work, but wear out...
  18. so is LEM still around? That FB page hasn't been...

    so is LEM still around? That FB page hasn't been touched in a long while. And I had no idea about the transition.
  19. Thread: flysky fs-bs6

    by jimbo74
    Replies
    2
    Views
    247

    should fit fine, doesn't look any bigger than the...

    should fit fine, doesn't look any bigger than the oe
  20. Replies
    620
    Views
    63,735

    Parts...

    Parts camehttps://uploads.tapatalk-cdn.com/20191208/76f0adce110d6207a181a207cf667d1b.jpg
  21. I just got brand new oe gears and they have...

    I just got brand new oe gears and they have surface rust...https://uploads.tapatalk-cdn.com/20191208/013a04ec16cb756655b8a90242249b9d.jpg
  22. Wow... I get spam emails this day from...

    Wow...

    I get spam emails this day from Charles. LEM has been defunct for years.
  23. Replies
    620
    Views
    63,735

    It's too over powered. I can't even get it up to...

    It's too over powered. I can't even get it up to full speed, and moving the throttle at all when it is moving will make it flip. I think I have surpassed 1/10th scale...

    I do have 1/8th scales...
  24. Replies
    11
    Views
    462

    Looks like tekno. Parts are easily had. I...

    Looks like tekno. Parts are easily had.

    I won't run RPM on this platform. I have several sets in a bin that are bent . They can't support the weight of the vehicle.

    That isn't to say I don't...
  25. Replies
    620
    Views
    63,735

    I haven't replaced one in 3 years..... And...

    I haven't replaced one in 3 years.....

    And with amazon, I am not worried about it. Also, I have a hobby shop within a half mile of where I work.

    My slash is going to get a lot less aggressive,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4