Search:

Type: Posts; User: mtc777

Page 1 of 14 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    7
    Views
    370

    Sure you can. With parallel connector you can...

    Sure you can. With parallel connector you can even charge packs with different capacities.
  2. Replies
    5
    Views
    210

    It is a density not brand. Any brand would do....

    It is a density not brand. Any brand would do.
    http://www.ebay.com/itm/Fastrax-Differential-Oil-3000wt-FAST61-3K-/282387641471?hash=item41bf9d747f:g:7nIAAOSwosFUVFNY




    The HR shock bodies...
  3. Replies
    5
    Views
    210

    I use 3000 wt shock oil and it works fine ...

    I use 3000 wt shock oil and it works fine ...
  4. Thread: Raising rockers

    by mtc777
    Replies
    2
    Views
    164

    http://www.ebay.com/itm/T-Works-3mm-Shim-Washer-Se...

    http://www.ebay.com/itm/T-Works-3mm-Shim-Washer-Set-0-05-0-1-0-2-0-3mm-each-10pcs-/162420428584?hash=item25d1030f28:g:SnkAAOSwGotWsEgl
  5. You don`t need many Celsius, a 30W soldering iron...

    You don`t need many Celsius, a 30W soldering iron should do the trick
  6. Replies
    15
    Views
    947

    HR ones, since they have the screw that holds...

    HR ones, since they have the screw that holds halves together, other brands dont have thatt, as far as I`m aware ....
  7. Replies
    8
    Views
    428

    Yes pretty much, I assembled them dozen of...

    Yes pretty much, I assembled them dozen of times............. I think the problem is that the air hole is on top and thread seems to be a bit short preventing the bladder to fully tighten.
  8. Replies
    8
    Views
    428

    Yes, that`s the idea Don`t bother,...

    Yes, that`s the idea





    Don`t bother, they are crap (leaking)
  9. Replies
    8
    Views
    428

    http://www.hot-racing.com/index.cgi?partnumber=VXS...

    http://www.hot-racing.com/index.cgi?partnumber=VXS15502;c=455

    This is your best option, you just need to use thicker oil, because the inner diameter is slightly bigger than the stock. I`m...
  10. Thread: RPM A-Arms

    by mtc777
    Replies
    11
    Views
    326

    You can`t install them wrong if you are aware of...

    You can`t install them wrong if you are aware of 2 facts:

    -All letters are facing UP
    -All pushrod mounts are on the lower arms.
  11. Aluminum, RPM pop out

    Aluminum, RPM pop out
  12. Replies
    18
    Views
    532

    In parallel yes, in series no

    In parallel yes, in series no
  13. Replies
    12
    Views
    722

    Take the motor apart, it might be some debris...

    Take the motor apart, it might be some debris inside or your bearings are toast
  14. Replies
    12
    Views
    722

    Thats why I asked if you try it with another...

    Thats why I asked if you try it with another ESC.......as far as I remember my NEU didn`t work with Velineon ESC
  15. Replies
    12
    Views
    722

    Have you tried with another ESC ?

    Have you tried with another ESC ?
  16. Replies
    12
    Views
    722

    It looks that one of the 3 wires has bad contact....

    It looks that one of the 3 wires has bad contact. Check/re-solder bullets and look for broken wire, on esc or motor
  17. Replies
    9
    Views
    225

    Motor draws current, not ESC. SW 3 can take...

    Motor draws current, not ESC.
    SW 3 can take around 80A, if thats what you mean
  18. Replies
    2
    Views
    481

    Here is the review...

    Here is the review
    https://www.youtube.com/watch?v=WSLq6WYxb_Y

    There is just one general rule to remember about Integy: STAY AWAY FROM IT
  19. Thread: Servo Help

    by mtc777
    Replies
    5
    Views
    323

    If the gears are ok than one of the wires that...

    If the gears are ok than one of the wires that goes to the pot (inside the servo) is broken. Replace the servo, stock servo is junk anyway
  20. Replies
    14
    Views
    1,635

    Disconnect the servo from the bellcrank and check...

    Disconnect the servo from the bellcrank and check for the buzz, if its gone then your steering assembly probably binds ....
  21. Replies
    3
    Views
    317

    Any thin CA will do the job

    Any thin CA will do the job
  22. Thread: Help!

    by mtc777
    Replies
    2
    Views
    204

    Unplug the servo and check if throttle works. In...

    Unplug the servo and check if throttle works. In that case servo is dead, it happens a lot
  23. Replies
    4
    Views
    507

    You can push wires a bit to a side and screw it....

    You can push wires a bit to a side and screw it. It is easier with a ball-end hex wrench. I have the same servo, and I dont remember having much trouble installing it....
  24. Replies
    38
    Views
    1,179

    I mixed 100k and 50k for center diff and it still...

    I mixed 100k and 50k for center diff and it still wheelies, so 100k will not take away tour wheelies
  25. Replies
    38
    Views
    1,179

    Don`t remember bu it was close to 2 weeks.... But...

    Don`t remember bu it was close to 2 weeks.... But we live in different countries, so thats a bit irrelevant...



    Mine come without ... You must also cut the axle and grind a flat spot for pinion...
Results 1 to 25 of 329
Page 1 of 14 1 2 3 4