Search:

Type: Posts; User: zedorda

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    19
    Views
    323

    A friend of mine has the older 57 chevy truck...

    A friend of mine has the older 57 chevy truck body painted white but without a backer coat with red leds inside that make the whole thing glow a hot pink and looks sweet at nite.
  2. Replies
    7
    Views
    184

    Fits like a glove in the LCG chassis. ...

    Fits like a glove in the LCG chassis.

    http://u.cubeupload.com/zedorda/IMG20190908230652364.jpg
  3. Thread: Center Diff

    by zedorda
    Replies
    11
    Views
    216

    As for design the TRA6780 is the best yet for the...

    As for design the TRA6780 is the best yet for the platform.
  4. Replies
    7
    Views
    184

    I use that setup in my Monster Slash 4x4 and it...

    I use that setup in my Monster Slash 4x4 and it works great with no temp problems yet. And you can gear it to the moon without needing much more than fans to keep stuff cool on the hot days.
  5. Thread: Strange Noise

    by zedorda
    Replies
    3
    Views
    108

    It is not likely completely worn out but it did...

    It is not likely completely worn out but it did wear enough to need tightening. As the slipper "breaks-in" or wears down from use it will get loose and not engage as fast and will sometimes get hot...
  6. The max speed possible without going down hill...

    The max speed possible without going down hill with that setup is about 25 mph. Was there not a "speed pinion" that came with the Stampede? Because a 13T pinion will get you a max of about 33 mph.
    ...
  7. Thread: Motor KV

    by zedorda
    Replies
    3
    Views
    135

    Thinking of Kv as being the factor for torque is...

    Thinking of Kv as being the factor for torque is an incorrect assessment. Watch this video: https://www.youtube.com/watch?v=BcuhdkCucGA at 12:50 he addresses this point but the whole video is full...
  8. Replies
    4
    Views
    154

    Lipos experience stress the more or less they are...

    Lipos experience stress the more or less they are from 50%. The farther from 50% up or down the more stress the cells undergo. Storage charge is just the least stressed state the cells can be at.
  9. I decided the 3674 1900kv was the wrong choice...

    I decided the 3674 1900kv was the wrong choice but sticking with the MAX10 SCT esc. Going to give a Banggood motor a try.

    A 3650 4300kv:...
  10. Replies
    11
    Views
    238

    Both those kits are as fast or faster than the...

    Both those kits are as fast or faster than the stock VXL system. All depends on weight of your rig and what gearing you choose to use. The brushed stampede has a plastic center drive shaft and might...
  11. Thread: Slipper clutch

    by zedorda
    Replies
    7
    Views
    132

    I would first try changing the locknut and if it...

    I would first try changing the locknut and if it still keeps getting loose you might want to look into getting a new slipper shaft. Sometimes it just happens that the cut threads are too smooth to...
  12. I don't use telemetry so I can't assist with whys...

    I don't use telemetry so I can't assist with whys just give the basic advice and if it didn't let you choose then you didn't do anything wrong. Are you sure the two are compatible to be used together?
  13. Replies
    13
    Views
    304

    I have started to use torx bits instead of hex...

    I have started to use torx bits instead of hex tools. Because they break/strip less often and when they do you can dig them out much easier since they don't fill the hole up so much.

    They are...
  14. Replies
    4
    Views
    75

    There is no easy way to get it out once it enters...

    There is no easy way to get it out once it enters from the holes in the rims. Before running in sand or water it is best to tape the holes to block them off. Then punch holes in the tires along the...
  15. Before doing updates you should always read the...

    Before doing updates you should always read the Changelogs to see if it is a good idea. The update could very well be working correctly.
  16. Replies
    5
    Views
    140

    Brushed motors are not meant for extended high...

    Brushed motors are not meant for extended high speed use. If used for racing they do not last long at all but that is why they(Titan 12T) are so cheap also. If you want speed best to go brushless. If...
  17. Replies
    24
    Views
    1,057

    I also use it on the outside after fresh paint...

    I also use it on the outside after fresh paint and sticker are applied. Helps keep them intact after serious road rash. Just reapply another coat after. But it does take forever to fully dry.
  18. The whole thing is a much longer story which I am...

    The whole thing is a much longer story which I am not going to explain fully here. I bet you can google it up the same way I did the first time. But the reasons the engineers left is the why I don't...
  19. Huge employee changes. Basically no one that...

    Huge employee changes. Basically no one that worked there during their raise and success in RC are there anymore. So it is far from the same company and skill set. With near no real progress in the...
  20. Replies
    20
    Views
    484

    You do know that if you put a larger spur gear...

    You do know that if you put a larger spur gear and larger pinion you can keep the same temp lowering gear ratio but not risk center drive shaft clearance issues plus keep the plastic end cap. The...
  21. Since what has happened at Tekin in the past...

    Since what has happened at Tekin in the past decade. I don't use any of their products anymore.
  22. Replies
    24
    Views
    1,057

    I used to use shoo goo and but have switched to...

    I used to use shoo goo and but have switched to Flex-seal clear. Still use drywall tape once in awhile but the Flex-seal clear allows me to use much less so the body doesn't start to get heavy.
  23. Replies
    20
    Views
    484

    Looks like you are running a pinion/spur combo...

    Looks like you are running a pinion/spur combo that are too small or the front bearing on the motor is worn badly.
  24. Replies
    8
    Views
    219

    To find out if you need a glitch buster take it...

    To find out if you need a glitch buster take it out. Then drive the rig fast and see if you lose and power or have stuttering while turning. If the power draw from the servo causes any noticeable...
  25. Replies
    1
    Views
    975

    I would bet you were doing more around 50mph....

    I would bet you were doing more around 50mph. Because over 50mph you will start to experience the front end lifting and possibly becoming airborne. The stampede/slash/rally/rustler all have this...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4