Search:

Type: Posts; User: Dcuda69

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    6
    Views
    105

    Good advice from 222. Might I suggest you invest...

    Good advice from 222. Might I suggest you invest in some good hex drivers(if you don't already have some,I use MIPs)........the tools that come with the truck are marginal at best. Good drivers will...
  2. Replies
    16
    Views
    617

    Pretty sure he was referencing the long time to...

    Pretty sure he was referencing the long time to get the packs..........mule train...meaning sloowwwww. Not literally a train.
  3. Replies
    7
    Views
    834

    Yep! Read the manual, you can set it for low...

    Yep! Read the manual, you can set it for low voltage detection to use with lipos. I ran mine on 2s for a short while until I installed a brushless setup.
  4. Replies
    11
    Views
    389

    Of all those I listed that 4074 is the torque...

    Of all those I listed that 4074 is the torque monster...backflips at will. With that said, my favorite is that Kershaw 3674 2700kv...geared the same(20/50) it is fast on 3s and stupid fast on 4s!...
  5. Replies
    5
    Views
    298

    This is a fair question!

    This is a fair question!
  6. Replies
    11
    Views
    389

    I have a HW SC8. I have run a bunch of motors...

    I have a HW SC8. I have run a bunch of motors with it. Traxxas/Castle 3670 2400kv, Kershaw Designs 3674 2700kv ,Velenion 3655 3500kv and now a RC Gearshop 4074 2150kv. All have seen 3s and everything...
  7. Sounds like a good plan. Didn't realize my box...

    Sounds like a good plan. Didn't realize my box was full...empty now.
  8. I've had MIPs on my Slash 4x4 for a few years...

    I've had MIPs on my Slash 4x4 for a few years now,never had an issue. Those are technically pin screws not grubs.....be absolutely sure you get the tip of that screw into the hole in the diff output....
  9. Sorry but.....why pair a 4s capable motor with a...

    Sorry but.....why pair a 4s capable motor with a 3s max esc? That SW4 is only 3s max with 5v/2A BEC. The $60 HW WP SC8 is 4s capable with a 6V/3A BEC. I think the 6s capable Mamba stuff is overkill...
  10. Personally I would want a 5mm shaft. There have...

    Personally I would want a 5mm shaft. There have been broken 3mm shafts on the 2400kv in the past. Pinions are cheap. No need to change the spur gear just be sure to buy 32 pitch pinions. I still run...
  11. Some great suggestions here. Another...

    Some great suggestions here. Another option(cheaper) is to search around ebay. One of my favorite combos in my Slash 4x4 is the Hobbywing WP SC8(still available about $60)paired with a Kershaw...
  12. Replies
    3
    Views
    392

    How do the Rustler 4x4 and Slash 4x4 compare...

    How do the Rustler 4x4 and Slash 4x4 compare weight wise? I have a Slash 4x4 Ultimate and use the VG springs mentioned above. Perfect fit for my modded(heavy) Slash. The Revo variable tuning kit for...
  13. Replies
    27
    Views
    895

    Not exactly sure what part you are referring to...

    Not exactly sure what part you are referring to but these exploded views should help you....once you figure out the part name post back and we can help you figure out if there are better options than...
  14. Glad it worked out for ya! I got that tip from...

    Glad it worked out for ya! I got that tip from someone over on the Slash 4x4 sub-forum....ElSob maybe? Happy to share what little I know! As for the beverage....,.that's my other hobby.....home...
  15. Must be the inner pins...5161? Sorry don't have...

    Must be the inner pins...5161? Sorry don't have the pkg anymore

    https://traxxas.com/explodedviews/E-Maxx-Brushless-39087-1-Front-Assembly
  16. If you're talking about that lower pin through...

    If you're talking about that lower pin through the a-arm/c-block, I use E-maxx pins and cut them to length on my Slash 4x4 ultimate

    http://i.imgur.com/EYU6HYV.jpg
  17. Replies
    13
    Views
    700

    My Slash Ultimate 4x4 is the beast with 1/8 power...

    My Slash Ultimate 4x4 is the beast with 1/8 power on 3s or 4s but my leftover rolling parts bin 2wd Rustler is a hoot to drive!!
  18. Thread: Upgrade Servo

    by Dcuda69
    Replies
    16
    Views
    485

    Can't help with the TSM question as my truck...

    Can't help with the TSM question as my truck doesn't have it but I can chime in on the Power HD 23kg. I like it.....throws my 2.8 Trenchers around like nothing. Definite improvement over stock. I run...
  19. I have an LCG with a 4074 2150kv running 20/50...

    I have an LCG with a 4074 2150kv running 20/50 gears. Drops right in after moving the receiver box up front. Stock(Ultimate) motor plate with a King Headz mount.

    http://i.imgur.com/xCrc678.jpg
  20. Replies
    42
    Views
    2,777

    What size can is that 2850kv motor? The bigger...

    What size can is that 2850kv motor? The bigger cans tend to make more torque and less heat.
  21. Replies
    13
    Views
    1,722

    Not a ton of help but... I have a GT with the VXL...

    Not a ton of help but... I have a GT with the VXL system. I bought it used and it came with Contact foams as well as the stock tires. I geared it up with the speed gears and threw a 3s pack in it. It...
  22. Replies
    22
    Views
    3,013

    I would be looking at the motor mount/slipper...

    I would be looking at the motor mount/slipper bearing/adapter. If it's still the stock plastic stuff there might be an issue there. Put a King Headz mount in with an aluminum bearing adapter and your...
  23. Replies
    6
    Views
    332

    Does this mean you found something? Maybe share...

    Does this mean you found something? Maybe share with the rest of us? Kinda the way forums are supposed to work.
  24. Replies
    42
    Views
    2,777

    Like these suggestions! I have a few motors for...

    Like these suggestions! I have a few motors for my Slash. One of my favorites is a Kershaw Designs 3674 2700kv(unfortunately no longer available). Paired with that HW SC8 on 3s is a blast....on 4s...
  25. Replies
    3
    Views
    466

    I put one of these in my Slash 4x4. Throws my 2.8...

    I put one of these in my Slash 4x4. Throws my 2.8 Trenchers around like nothing. I run a HW WP SC8 esc at 6.0v (IIRC) I do run a gltchbuster but not sure it's needed.
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4