Search:

Type: Posts; User: Jrz13

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    404

    I run traxxas part number 5041 in the...

    I run traxxas part number 5041 in the differential. The weight you use in the carrier kinda depends on what your doing with it. I run 80k up front amd 100k in the rear, from the fatory there is 30k...
  2. Thread: Motors on hand

    by Jrz13
    Replies
    4
    Views
    197

    Youll have much more gearing options, better...

    Youll have much more gearing options, better temps and runtimes with the 2200kv. The 4000kv is a little high for the weight of the rustler 4x4
  3. Replies
    12
    Views
    268

    A center diff isn't stock on the rustler. Should...

    A center diff isn't stock on the rustler. Should keep it from doing wheelies though
  4. Replies
    12
    Views
    268

    That is the factory rustler 4x4 wheelie bar and...

    That is the factory rustler 4x4 wheelie bar and it sucks. RPM makes a kit that uses the 2wd rustler wheelie bar. That one works much better
  5. Replies
    6
    Views
    305

    Kinda sounds more like a bad bearing

    Kinda sounds more like a bad bearing
  6. Thread: Rustler LSD?

    by Jrz13
    Replies
    14
    Views
    787

    For the front diff i wouldnt go heaver than 100k...

    For the front diff i wouldnt go heaver than 100k so it still takes turns pretty well
  7. Thread: Rustler LSD?

    by Jrz13
    Replies
    14
    Views
    787

    I think 500k may be a little too thick for the...

    I think 500k may be a little too thick for the front. Could cause alot of torque steer.
  8. Thread: Rustler LSD?

    by Jrz13
    Replies
    14
    Views
    787

    If your looking to nearly lock the rear, go 1...

    If your looking to nearly lock the rear, go 1 million wt.
  9. Thread: Rustler LSD?

    by Jrz13
    Replies
    14
    Views
    787

    +1 on keeping your slipper clutch. I run some...

    +1 on keeping your slipper clutch. I run some parking lot racing and just built a track in my yard. I'm running 80k front and rear with xo1 differentials and spiral cut gears. The diff has some slip...
  10. Replies
    10
    Views
    503

    +1 on the Tekno. I run these front and rear with...

    +1 on the Tekno. I run these front and rear with 0 problems
  11. Both of those look awesome! Good job

    Both of those look awesome! Good job
  12. Replies
    2
    Views
    627

    The xo1 differential carrier gets rid of most of...

    The xo1 differential carrier gets rid of most of the slop https://traxxas.com/news/slash-4x4-differential-upgrade
  13. Replies
    18
    Views
    727

    I add a little blue locktight on my axle stubs...

    I add a little blue locktight on my axle stubs when installing wheel nuts
  14. Replies
    13
    Views
    600

    +1 orange locktight holds stronger than blue on...

    +1 orange locktight holds stronger than blue on screws that vibrate loose
  15. Replies
    4
    Views
    271

    Mine was missing the front right inner bearing....

    Mine was missing the front right inner bearing. Didnt really notice till I broke a driveshaft and was repairing it.
  16. Thread: Toe Links

    by Jrz13
    Replies
    7
    Views
    571

    I run the traxxas 6742, their plastic and flex a...

    I run the traxxas 6742, their plastic and flex a bit on big jumps. But I havent broke one yet and I run proline badlands which are some pretty big tires.
  17. Replies
    6
    Views
    554

    That looks awsome! Post some pictures when you...

    That looks awsome! Post some pictures when you get it all painted up
  18. Replies
    13
    Views
    600

    A hardened pinion gear would wear the spur more...

    A hardened pinion gear would wear the spur more quickly but shouldnt just immediately tear it up. I run robenson racing extra hard pinion and hardened spur, they hold up to some serious abuse.
  19. Replies
    7
    Views
    438

    The chassis has a pretty good amount of flex,...

    The chassis has a pretty good amount of flex, expecially with large jumps. When you tighten the grub screw on the drive shaft adaptor make sure its in its rear most position. The little bit of slop...
  20. Thread: Roller Questions

    by Jrz13
    Replies
    10
    Views
    534

    Building up a roller is an awsome option. I did...

    Building up a roller is an awsome option. I did the same with my rusty. Givesnypu an opertunity to use left over parts and or the parts you want not just what comes in an rtr.
  21. Replies
    2
    Views
    385

    Now I'm also looking at the tekin pro4hd 3500kv....

    Now I'm also looking at the tekin pro4hd 3500kv. But it's like twice the price
  22. Replies
    2
    Views
    385

    Rustler 4x4 motor suggestions

    Im doing some shopping for a new motor for my rustler 4x4. Im running a mamba x with a 1410 3800kv with 3s batteries. Shes pretty fast but the motor gets pretty hot and runtimes are short. So im...
  23. Thread: Slash bash

    by Jrz13
    Replies
    10
    Views
    529

    First off congrats on your putchace. Running 3s...

    First off congrats on your putchace. Running 3s your going to want to have a couple spare driveshafts on hand. The shock shafts and caps are a big week point. Traxxas has hardend shafts and anluminum...
  24. Replies
    5
    Views
    343

    Ive seen some magnetic body mounts out there. Not...

    Ive seen some magnetic body mounts out there. Not sure how they would hold up to big jumps and such though
  25. Replies
    3
    Views
    319

    Looks good!

    Looks good!
Results 1 to 25 of 67
Page 1 of 3 1 2 3