Search:

Type: Posts; User: 222

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 30 minute(s) ago.

  1. Replies
    4
    Views
    86

    I would get XT150ís instead of xt90ís for the...

    I would get XT150ís instead of xt90ís for the Xmaxx. That esc is rated at 160a. Just some food for thought.
  2. Replies
    14
    Views
    638

    I might be one of the few, but I have used bullet...

    I might be one of the few, but I have used bullet connectors for a few years now and have never had issues with soldering them on, or issues with heat or failures. Easy to install and work very...
  3. Thread: O.G. diffs

    by 222
    Replies
    8
    Views
    4,024

    Wish I would have known about this when I had the...

    Wish I would have known about this when I had the opportunity to fix my ERBEís diffs. They broke on me just about every run! My ERBE ended up in a parts bin collecting dust in a bunch of pieces!! ...
  4. Replies
    6
    Views
    110

    I completely understand. I run dual servos on my...

    I completely understand. I run dual servos on my summit and I spent the better part of a couple hours getting them aligned. I was way OCD about it LOL! But Iíve not had a single issue with them in...
  5. Replies
    6
    Views
    110

    Mine fit like this on my 1/10 summit. I just...

    Mine fit like this on my 1/10 summit. I just screwed it down, making sure it stayed straight. You can try using the included rubber grommets as well and see if they help fill in the gaps. Worth a...
  6. Replies
    11
    Views
    233

    Yep, just replace the dual battery harness and...

    Yep, just replace the dual battery harness and use just 2 wires and one connector. Should work just fine that way. As for motor/esc combo, the castle creations mamba x and 2400kv motor seem to do a...
  7. Replies
    8
    Views
    352

    Place that thing into a bucket of saltwater. Let...

    Place that thing into a bucket of saltwater. Let it remain there for a couple days at least to make sure itís discharged. Then dispose of it properly.
  8. Thread: Summit Battery

    by 222
    Replies
    3
    Views
    137

    I donít think the stock esc is rated for 6s. You...

    I donít think the stock esc is rated for 6s. You could remove one connector from the esc to batteries, then just run one of your 3s batts. But as I posted earlier youíll need to have some way of...
  9. Thread: Summit Battery

    by 222
    Replies
    3
    Views
    137

    Yes and no. It wonít recognize the cell count as...

    Yes and no. It wonít recognize the cell count as it requires minimum of 4s to get proper voltage for the LVC Iím pretty sure. You can bypass this by placing it into NIMH mode but youíll need some...
  10. The main thing that got me bad on the V1 ERBE,...

    The main thing that got me bad on the V1 ERBE, was diffs. I went through diffs almost every run even on 4s. They just wouldnít hold up to even mild bashing. I ended up with a $1200 parts bin for a...
  11. Replies
    2
    Views
    210

    Sounds like either a stripped spur gear or one...

    Sounds like either a stripped spur gear or one that is missing a tooth, or one of your diffs is going out, most likely the rear one.
  12. If it runs off the receiver then itís most likely...

    If it runs off the receiver then itís most likely 6v, and for low beams just drop the voltage a bit. 5v should do the trick.
  13. Thread: Fried Rx, ESC??

    by 222
    Replies
    5
    Views
    321

    So sorry. Was looking at the specs for the max...

    So sorry. Was looking at the specs for the max 6. You are 110% correct. Max 5 is 200a ESC. Definitely want XT150ís or 8mm bullet connectors for it. No way XT90ís to traxxas adapters going to...
  14. At 6yrs old I would venture to say your battery...

    At 6yrs old I would venture to say your battery needs to be replaced. Itís most likely not holding voltage under a load, thus the reason you can see the tires spin fast when itís off the ground. ...
  15. Thread: Fried Rx, ESC??

    by 222
    Replies
    5
    Views
    321

    Get rid of the adapters. I would solder traxxas...

    Get rid of the adapters. I would solder traxxas connectors or XT150ís onto both the ESC and batteries. The way you have it now itís a choke point. You may be starving the ESC for power this...
  16. Thread: 17mm wrench

    by 222
    Replies
    6
    Views
    398

    Get yourself a thin walled 17mm socket, a 6Ē...

    Get yourself a thin walled 17mm socket, a 6Ē extension, and a 3/8 ratchet. You can find the socket off eBay for relatively cheap as well as the 6Ē extension. Something like this may not require an...
  17. Replies
    33
    Views
    1,129

    If you want to keep it all traxxas and want a...

    If you want to keep it all traxxas and want a good upgrade, look into the 2255 servo. Itís a normal size one, the kit for installing it may or may not have come with the truck.
  18. Replies
    16
    Views
    598

    SMC batteries has some 4800mah ones for under...

    SMC batteries has some 4800mah ones for under $30. They make pretty good batteries. ...
  19. Replies
    5
    Views
    549

    One is plenty. I used a JR 9000t for a long time...

    One is plenty. I used a JR 9000t for a long time on my 1st gen Erevo. Worked perfect. And it was only 300oz of torque. 400oz of torque at 6vdc is plenty. Donít see where traxxas lists the amount...
  20. Replies
    16
    Views
    598

    Try SMC or Gens Ace. I know that SMC are quality...

    Try SMC or Gens Ace. I know that SMC are quality batteries. Iíve heard good things about Gens Ace. There are other places to get batteries for cheap, but we are not allowed to speak of that place. ...
  21. Replies
    13
    Views
    538

    When you first get it, charge it at low at a low...

    When you first get it, charge it at low at a low amperage. Like no more then 1a. This will ensure that it doesnít get hot while charging. Heat is bad for them as with all batteries. It will take...
  22. Replies
    5
    Views
    292

    There is a big difference between ďrestingĒ...

    There is a big difference between ďrestingĒ voltage, and voltage ďunder loadĒ. Your batts may well have been hitting the LVC when you applied power as said above. A quality battery is a good...
  23. Replies
    10
    Views
    926

    Well for one in your first post you state that...

    Well for one in your first post you state that the spur gear you replaced the one that got chewed up with was not the stock 38t but rather a 36t. You should have had to set the mesh for this one. ...
  24. Replies
    10
    Views
    926

    Well said!!!

    Well said!!!
  25. The MIP drivers will no doubt remove the screws. ...

    The MIP drivers will no doubt remove the screws. Just bought my first one, and I will say they are made very well!! I also use RDS hex drivers, and they are well made too. You pay more for them,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4