Search:

Type: Posts; User: JavaBlack

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    25
    Views
    721

    I have been tempted with running the the G4...

    I have been tempted with running the the G4 chassis it is definatly very clean. The only thing i worry about is not being able to mount up my rc-solutions roll cage. Maybe i could custom fab some...
  2. Replies
    12
    Views
    491

    That is not ture i have 2x 3S 5000 flightmax...

    That is not ture i have 2x 3S 5000 ********* lipos under each side of my cage. i have more of a problem with the lipos fitting into the stock batery box of the emaxx.
  3. Replies
    12
    Views
    491

    I put to 6mm bullet conectors on mine, along with...

    I put to 6mm bullet conectors on mine, along with matching the conector on the lipos. I took some time planing it out so i can switch from a single pack to two in series with no harness.
  4. Replies
    20
    Views
    663

    When i get my gears in i will strap on the gps...

    When i get my gears in i will strap on the gps and try to get an acurate number.
  5. Replies
    7
    Views
    1,046

    I am using (2) 3s lipos for better weight balance...

    I am using (2) 3s lipos for better weight balance plus i do not have anywhere to put one big single 6s lipo.
  6. Thread: durability?

    by JavaBlack
    Replies
    7
    Views
    247

    That is a tough call in my opnion the stock...

    That is a tough call in my opnion the stock e-maxx can be pretty brittle. Even more so durring the cold months, but with some simple upgrades my truck is really pretty tough. Some aluminum bulkheads...
  7. Replies
    236
    Views
    7,900

    That is good news i always like their design but...

    That is good news i always like their design but i was not a fan of modifying something that was already custom made.
  8. Replies
    11
    Views
    472

    The review sounds pretty positive i may look into...

    The review sounds pretty positive i may look into picking up a set to go along with the cage. H.C. post up some detailed pictures when you can i am hopping they turn out really nice.
  9. Replies
    19
    Views
    1,759

    I did not think of that my one pad that did not...

    I did not think of that my one pad that did not explode was only showing wear on the side closest to the center not on the whole pad. Hopefully i'll get all my parts in tomorrow from my local shop...
  10. Replies
    19
    Views
    1,759

    When i started looking into my problem a little...

    When i started looking into my problem a little more i think i over tightened the three screws that held the hub with the slipper pads to the actual spur gear. It looks like it caused the pads to...
  11. Replies
    15
    Views
    785

    I am using the rc-solutions front and rear skids....

    I am using the rc-solutions front and rear skids. They are not titanium but made of a "spring steel" i have hit some curbs, trees and just about everything else Hard the plates have not bent out of...
  12. Replies
    19
    Views
    1,759

    I could do that since i am needing to rebuild the...

    I could do that since i am needing to rebuild the transmision anyway, if i start it moving under low power it should not destroy to much.
  13. Thread: New Shoes

    by JavaBlack
    Replies
    15
    Views
    426

    Think about on a term of full size cars, on daily...

    Think about on a term of full size cars, on daily driver cars if you push in the tred of your tires they range from firm to hard, and you only have to change them every 2 or 3 years depending on...
  14. Replies
    19
    Views
    1,759

    The same thing just happened to me, i had the...

    The same thing just happened to me, i had the slipper adjusted a quarted out from the bottom. I had just finished getting all my parts in and after a month of not running i was excited to have it...
  15. Replies
    11
    Views
    472

    I am using their roll cage along with the front...

    I am using their roll cage along with the front and rear skid plates, you will not get any complates from me. As far as the shock towers i have been waiting on some reviews to come out.
  16. Thread: New Shoes

    by JavaBlack
    Replies
    15
    Views
    426

    The harder rubber is closer to a plastic.

    The harder rubber is closer to a plastic.
  17. Replies
    34
    Views
    836

    I have been thinking about picking up and erevo...

    I have been thinking about picking up and erevo and swaping all the eletronics between the trucks making the emaxx waterproof again as a basher and putting the MMM in the revo for speed and possibly...
  18. Replies
    9
    Views
    497

    Instead of paying 50 or more for a powersupple i...

    Instead of paying 50 or more for a powersupple i built my own for roughly 35 that can out preform one 2 or 3 times as much. Check it out.
  19. Replies
    9
    Views
    497

    Those whould be the ones, I'm expecting them to...

    Those whould be the ones, I'm expecting them to get her saturday or monday hopefully sooner than later.
  20. The 62/22 = 2.81, 68/24 = 2.83 and 68/25 = 2.72....

    The 62/22 = 2.81, 68/24 = 2.83 and 68/25 = 2.72. So the 24T will be the clostest with slightly more torque.
  21. ^ That is what i have seen as the most common, i...

    ^ That is what i have seen as the most common, i think a little more speed can be gotten out of 65/25 but i have not tested it yet. As far as the driveline everything that i have read tells me that...
  22. Replies
    9
    Views
    497

    Mamba Combo and 3S'

    I just ordered two 3S lipos for my new Mamba Combo from Hobby City. My idea is that i am going to run the two packs in series so i can get the most out of the ESC, but i was wondering if i could run...
  23. Replies
    16
    Views
    416

    +1 for maryland, it nice to get a deacent amount...

    +1 for maryland, it nice to get a deacent amount of snow to bad it is all going to freeze. This really make my want to get lipos and some new gearing for the new MMM. By the way where in maryland are...
  24. This is exactly what i did not the cleanest...

    This is exactly what i did not the cleanest design but i have yet to have any problem with it.
  25. I was thinking about that i just have not done it...

    I was thinking about that i just have not done it yet to try maybe i'll give it a shot later and post up how it worked out.
Results 1 to 25 of 44
Page 1 of 2 1 2