Search:

Type: Posts; User: olds97_lss

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    24
    Views
    1,784

    This is the thermometer:...

    This is the thermometer:
    https://www.rcjuice.com/hobbystar-ht-101-infrared-thermometer.html

    Oddly, I just put the OEM tires on my outcast tonight because they are lighter than the 3.8" trenchers...
  2. Replies
    24
    Views
    1,784

    Latest run from last weekend. I dropped in an HPI...

    Latest run from last weekend. I dropped in an HPI Tork 2200kv 4074 to replace the traxxas/castle of the same spec motor. I also replaced the servo since the last post and the drag link (noted in...
  3. Replies
    22
    Views
    18,000

    My latest run. Trying to figure out the...

    My latest run. Trying to figure out the hesitation issue... when in doubt, replace everything! lol!

    I had a max10 sct and a couple motors I could use, went with a hobbystar 3665 3100kv. Those...
  4. I ran the max10 sct/3660sl in mine for a bit....

    I ran the max10 sct/3660sl in mine for a bit. Ended up running a hobbystar 3665/3100kv motor which ran cooler and performed better on 3S. The 3660sl ran hot. The 3665 did ok, but I ended up ditching...
  5. I run the t-bone rear skid/wheelie bar. Pretty...

    I run the t-bone rear skid/wheelie bar. Pretty sure it was from the v1 and I had to make different holes for it to fit the v2. Looks like they changed the design a bit for the 2.0:...
  6. Replies
    3
    Views
    113

    I didn't run the Max10 Sct/3660SL-3200kv in a...

    I didn't run the Max10 Sct/3660SL-3200kv in a rustler, but I did run it in a stampede 4x4. I ran it with 3S only. It was more capable than the vxl-3s/3500kv system, not extremely so, but did run a...
  7. Integy has one for the slash/rustler:...

    Integy has one for the slash/rustler:
    https://www.integy.com/st_prod.html?p_prodid=19319

    It's for the LCG chassis.

    Not sure why I didn't just search for it on their site... tried skimming...
  8. Forgot, integy has a set with bearings as well: ...

    Forgot, integy has a set with bearings as well:

    https://www.integy.com/st_prod.html?p_prodid=8463

    Not sure how good they are, but appears they use the stock king pin/shoulder bolts.
  9. Replies
    14
    Views
    477

    Integy offers some with bearings as well. I knew...

    Integy offers some with bearings as well. I knew I ran across another set besides the GPM ones:
    https://www.integy.com/st_prod.html?p_prodid=8463

    Not sure how good they are, but appears they use...
  10. Good point. I'm running 19/54 which seemed to...

    Good point. I'm running 19/54 which seemed to work well with the old motor. Got a 20T coming in the mail to try with the new motor after I see how it does.
  11. Replies
    78
    Views
    6,466

    Probably also matters if your running on grass a...

    Probably also matters if your running on grass a lot or not. I know my trucks run far cooler at skate parks than they do when I run them at the grass bmx track. Granted, I'm running WOT more often at...
  12. It should. I run a traxxas/castle 4074 2200kv in...

    It should. I run a traxxas/castle 4074 2200kv in my stampede with a slash chassis. I'm powering it with a blx185 esc (150A). I didn't really have any issues installing it. I do have the traxxas HD...
  13. Replies
    3
    Views
    155

    The v2 is far better than the v1. I had a v1 for...

    The v2 is far better than the v1. I had a v1 for 3 years that I run on 4S and got a v2 roller last year so I could run 6S. I transferred some of my upgrades to it as well as the electronics I was...
  14. Replies
    1
    Views
    94

    I got my v2 used and it came with that on the...

    I got my v2 used and it came with that on the rear/center. Not sure why the front doesn't have one since they appear to come as a set. I've been running it almost a year on 6S with trencher 3.8 tires...
  15. Replies
    13
    Views
    373

    I prefer to run mine down to the connection point...

    I prefer to run mine down to the connection point on the other end of the pushrod. Then it helps to protect all the connections vs just the shock end. I made my own out of covered cable I picked up...
  16. Replies
    6
    Views
    171

    I don't have much aluminum aftermarket on my...

    I don't have much aluminum aftermarket on my ERBEv2. Just the rockers and a homemade rear chassis brace. I bent the traxxas aluminum one pretty good. ...
  17. Replies
    4
    Views
    116

    I've been running the plastic 54T with FLM center...

    I've been running the plastic 54T with FLM center diff cup in my stampede on 3S with BLX185/2200kv 4074 in my stampede. So far, it's held up fine. I did order a few to have on hand though. I was...
  18. Replies
    11
    Views
    282

    I'm glad I upgraded mine a long time ago now that...

    I'm glad I upgraded mine a long time ago now that I have a 4074 motor bolted to it. I run the traxxas upgraded plate with the HCG king heads bearing mount as well in my slampede. The bearings last so...
  19. I can't recall if they intended you to use the...

    I can't recall if they intended you to use the stock hinge pin on the bottom or not, already forgot. Either way, I use 3x50mm black oxide bolts, a 1mm (might be 1.5mm) shim/washer and a locknut to...
  20. Replies
    14
    Views
    477

    It may have come with hinge pins... I can't...

    It may have come with hinge pins... I can't recall, I used 3x50mm bolts with locknuts and cut them down so they are fully captured and I hate using c-clips if I don't have to. The kingpins use the...
  21. 32P on my slampede, running 3S. 19/54 with 2.8...

    32P on my slampede, running 3S. 19/54 with 2.8 trenchers with the blx185 and traxxas older 2200kv motor from my ERBEv1:
    https://traxxas.com/products/parts/motor/3376waterproof2200motor

    The motor...
  22. So far, they are holding up well. I have a couple...

    So far, they are holding up well. I have a couple pretty hard bash sessions on them.
  23. Images aren't showing in the original posts as I...

    Images aren't showing in the original posts as I changed where I house them.

    This is the shoulder bolt:
    The shoulder bolt, I think my micrometer moved on me as the length of the threaded + the...
  24. Replies
    14
    Views
    408

    It could just be that the bearing seats aren't...

    It could just be that the bearing seats aren't perfectly correct for the bearing crush space, so when you tighten the wheel, it puts side load on the bearings. That will fry a bearing within minutes....
  25. Replies
    14
    Views
    477

    I tried traxxas and aftermarket alloy ones (hot...

    I tried traxxas and aftermarket alloy ones (hot racing, atomik) on my stampede and they get slop in them pretty quick (read a summers worth of bashing) and I found some that use bearings for the king...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4