Search:

Type: Posts; User: nebulous.cow

Page 1 of 15 1 2 3 4

Search: Search took 0.03 seconds.

  1. This^^^^ Quality information there indeed! I...

    This^^^^ Quality information there indeed!

    I did nitro helicopters as well, and tuning them was a handfull. 3 needles, and heli engines have the worst tendencies when it comes to needles...
  2. Replies
    8
    Views
    75

    Ther servo is supposed to have more range than...

    Ther servo is supposed to have more range than the linkage can move. You see the coil spring on the hinge for the linkage? This coil spring is there to absorb the extra range of motion from the...
  3. Id say what happens sometimes is the needles...

    Id say what happens sometimes is the needles become out of sync. If your high is really lean and your low is really rich, or vice versa, they can affect each other for a little bit, and create the...
  4. Replies
    29
    Views
    1,188

    Yeah my worn out piston picture shows that it may...

    Yeah my worn out piston picture shows that it may look totally good, and be totally worn out. Like it was mentioned, its the tolerance between the piston and sleeve that allow compression at...
  5. Replies
    29
    Views
    1,188

    Interesting. Only a little over a gallon for...

    Interesting. Only a little over a gallon for real? That's quite a short life span man. I have an old OS 18 motor in my classic Maxx, and it probably has about 20 gallons on the same motor. It's old,...
  6. Replies
    29
    Views
    1,188

    Dang man that is a beaten up motor! Definitely...

    Dang man that is a beaten up motor! Definitely power up program, or if you see yourself using it a lot in the future, the OS goes a long way. I bought my revo 3.3 new this past year, and it was...
  7. Replies
    5
    Views
    308

    I would go fully sealed honestly. The friction is...

    I would go fully sealed honestly. The friction is negligible, but more importantly, if (or when) another gear explodes inside the trans, bits of the gear (or just gear dust from long term use in the...
  8. Replies
    5
    Views
    308

    +1 replace the bearings. Transmission bearings...

    +1 replace the bearings. Transmission bearings are really important, like redux said, they maintain a very specific tolerance between gears, and any play can cause the shafts to wobble in and out of...
  9. Honestly I just sell or throw those away....

    Honestly I just sell or throw those away. Chargers that come with RTRs or kits are usually garbage in one way or another.
    That said, I have extremely high standards for my chargers because I build...
  10. Bummer to hear dude, it happens. I would tell...

    Bummer to hear dude, it happens. I would tell them it had the engine problem immediately, so that they are more likely to help you.

    I quit using traxxas motors all together, and it hurt my wallet...
  11. Break in is the most likely time for an engine to...

    Break in is the most likely time for an engine to fail, because the parts fit the tightest, rub the hardest, and any manufacturing issues are likely to cause issues here.

    Loud engine sounds when...
  12. Replies
    15
    Views
    569

    I thought the same thing double G. I had bearings...

    I thought the same thing double G. I had bearings go out in one quart on a new 3.3 in my revo. Contacted them and the representative replied with this:

    The only warranty is the 30 day electronic...
  13. Replies
    15
    Views
    569

    Sorry to hear the nitro frustration story my...

    Sorry to hear the nitro frustration story my friend. Hang in there, the Revo is a super fun truck, it will pay off I promise.

    Since it's your first car, let me lay down the line for ya. Most rc...
  14. Replies
    4
    Views
    1,235

    Suspension is a deeeeeep rabbit hole for the...

    Suspension is a deeeeeep rabbit hole for the revo. I felt the same way about mine, so what I did was:

    -move the suspension linkage to the middle hole on the lower arms.
    -Green and gold springs...
  15. Replies
    14
    Views
    1,282

    Honestly for bashing if the weight wasn't...

    Honestly for bashing if the weight wasn't massive, I would do it lol. If it means I can keep my engine in the perfect temp range the entire bashing session, then that's a huge win. All you have to do...
  16. Replies
    3
    Views
    181

    Yeah it's hard to judge. Best thing with used...

    Yeah it's hard to judge. Best thing with used engines is if you can see the engine running, or even if you can get an opportunity to drive and tune the car yourself, then you know what you are...
  17. Might get better responses in the TRX Engines...

    Might get better responses in the TRX Engines forum btw! :)

    If your motor is gunked at all, I'd recommend a thorough clean out. It's relatively easy, free, and takes only a little time.

    Inside...
  18. Replies
    14
    Views
    1,282

    For traxxas motors with the longer glow plug ( i...

    For traxxas motors with the longer glow plug ( i assume the 0.15 has the same long plug like the 3.3) the OS LC3 Hot long-reach glow plug has worked really well for me, running 30% and in the desert...
  19. Replies
    14
    Views
    1,282

    I have gone down this path as well. I actually...

    I have gone down this path as well. I actually have a partially completed hand-made brass radiator, I never finished brazing the fins.

    With some pressure tolerance, you could actually make a...
  20. Replies
    39
    Views
    3,907

    Holy wow! Hahaha that's insane! Definitely what I...

    Holy wow! Hahaha that's insane! Definitely what I want as well!

    There's gotta be other pipes that work just as well, or very close to. If I had to guess, that pipe looks like its a "top end"...
  21. Replies
    17
    Views
    455

    Huh interesting.... I stand corrected, thanks! My...

    Huh interesting.... I stand corrected, thanks! My classic maxx is FOC from a previous owner, and it bucks, but drive like a dream still. I would assume the Revo trans is different though, but...
  22. Replies
    3
    Views
    181

    This is an incredibly hard thing to evaluate...

    This is an incredibly hard thing to evaluate without pictures or seeing it in person. There's a handful of things to check, but even if all those things are in good conditions, it may not be a good...
  23. Replies
    17
    Views
    455

    The forward only conversion does not remove the...

    The forward only conversion does not remove the OWB that engages for first gear, it cannot. The OWB engages when you hit the throttle in first gear, and then when second gear kicks in due to the...
  24. I stand corrected about my last assumption -...

    I stand corrected about my last assumption - looks like Traxxas does say the 15 runs at 300+ degrees. That to me sounds insane, but I guess if that's what the manufacturer says, keep leaning it! Lol....
  25. Replies
    17
    Views
    455

    Grizzly, its the one way slipping and grabbing...

    Grizzly, its the one way slipping and grabbing suddenly inside the transmission. the truck literally kicks a couple times when you roll away from a stop every time, and then finally grabs and rolls...
Results 1 to 25 of 352
Page 1 of 15 1 2 3 4