Search:

Type: Posts; User: luckybobb

Page 1 of 10 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    9
    Views
    169

    welcome back. I was the same way was out of it...

    welcome back.

    I was the same way was out of it for about 10 years and broke it out a few years ago because my son was old enough to have some fun with it.

    The rustler is nice and sturdy and...
  2. Replies
    5
    Views
    723

    Did the same thing a few years ago and yes with a...

    Did the same thing a few years ago and yes with a brushless the old tranny gears will probably not last one battery (mine lasted about 5 minutes).
    Sorry I can't remember what my gearing is since my...
  3. Replies
    16
    Views
    730

    Thanks for the clarification. Haven't had it in a...

    Thanks for the clarification. Haven't had it in a while and couldn't remember exactly what you can change that way.
  4. Replies
    16
    Views
    730

    castle used to have the ability to change those...

    castle used to have the ability to change those values using the remote.
    Not sure if they stillbdo or not and it was a little bit of a lengthy procedure.
  5. Replies
    5
    Views
    79

    exploded view

    Anyone know if you can still get the exploded views for the rustler?
    I looked on the site but can't seem to find them.
  6. Replies
    18
    Views
    867

    another question I didn't see asked is are you...

    another question I didn't see asked is are you breaking in these motors when you buy them and are you doing any maintenance on them?
  7. I know there are better out there but I have been...

    I know there are better out there but I have been using this one for a few years and it hasn't given me any problems.
    ...
  8. Replies
    12
    Views
    209

    I don't have any experience with the piggybacks...

    I don't have any experience with the piggybacks but I love the big bores I put on my rusty.
  9. Replies
    13
    Views
    265

    Could als be a loose/worn slipper clutch or the...

    Could als be a loose/worn slipper clutch or the pin that holds the gear on the top shaft inside the transmission may have broken. If the pin broke the gear woulbe on tight enough to turn the wheels...
  10. Replies
    9
    Views
    275

    Happened to me a while ago with my rustler. the...

    Happened to me a while ago with my rustler. the truck was completely submerged for about 25 min. When I got it out I took all of the electronics (none of them were waterproof) and let them sit in...
  11. Replies
    15
    Views
    491

    Also recommend every so often take the motor out...

    Also recommend every so often take the motor out and flush it with motor cleaner and once it is dry re oil the bushings on both ends.
  12. Replies
    6
    Views
    793

    If i am not mistaken the adapter will be fine for...

    If i am not mistaken the adapter will be fine for charging the battery, but i don't think the molex is going to handle the draw of the brushless system.
    I will admit that i am not too familiar with...
  13. Also looks like you may want to check the preload...

    Also looks like you may want to check the preload spacers, they look to be adjusted two different heights.
  14. Replies
    4
    Views
    94

    Is this an analog (MHz) or digital (2.4ghz)

    Is this an analog (MHz) or digital (2.4ghz)
  15. Replies
    22
    Views
    746

    Not sure what radio you are using but i have run...

    Not sure what radio you are using but i have run a 3800 and 4400 motor on nimh and the only time experienced cogging is back when i had an fm radio when i switched to 2.4ghz the problem disappeared.
  16. Replies
    5
    Views
    498

    If you are charging them at the same rate the...

    If you are charging them at the same rate the 4200 will take longer then the 3000.
    As far as the voltage the 8.4 is a nominal voltage the max voltage for njmh is 1.6 volts per cell so the 7 cell can...
  17. Replies
    11
    Views
    405

    If the pinion gear is spinning the motor is good...

    If the pinion gear is spinning the motor is good and it should only take a few bucks for a new spur to get it up and running. Just make sure to set the mesh correctly or it won't take long to...
  18. Did the samething awhile ago and if i remember...

    Did the samething awhile ago and if i remember correctly the top shaft is different and will need th be replaced.
    You will also need a new spur gear and two bearings for it along with the slipper...
  19. Replies
    5
    Views
    118

    Thanks for the info guys.

    Thanks for the info guys.
  20. Replies
    5
    Views
    118

    motor question

    Thinking of building a 2wd stampede, I have a 2pole 4400kv brushless on hand and i was wondering if this motor would work or if I am going to have hrat issues?

    Thanks for any insight you guys can...
  21. Replies
    10
    Views
    147

    Also may want to chech that they are plugged in...

    Also may want to chech that they are plugged in to the correct slots.
  22. Replies
    33
    Views
    425

    Some of the problems could be related to the fact...

    Some of the problems could be related to the fact that with that motor (had the same onein a rustler) the nimh will work but will not be ableto supply with the amps it really needs. I ran it with a...
  23. Replies
    33
    Views
    425

    Is this a nimh battery and if it is are you sure...

    Is this a nimh battery and if it is are you sure the lvc is turned off? If it is a nimh in lipo mode the voltage drop when the throttle is engaged could be triggering the cutoff.
  24. Thread: Grave digger

    by luckybobb
    Replies
    8
    Views
    880

    Not sure if it is the same body that came with it...

    Not sure if it is the same body that came with it but there are some grave digger bodies by parma for less than thirty dollars on amazon.
  25. Replies
    3
    Views
    717

    Not sure where you are looking but i just...

    Not sure where you are looking but i just downloded the exploded view from the wbsite.
Results 1 to 25 of 248
Page 1 of 10 1 2 3 4