Search:

Type: Posts; User: oakvad

Page 1 of 18 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    52
    Views
    3,898

    Wow! Ya that's super curious. Only heat issue...

    Wow! Ya that's super curious. Only heat issue I've had so far is running with dust cover, seams to heat up a bit. Im also not running a motor fan yet either.

    Sent from my Nexus 6P using Tapatalk
  2. Replies
    52
    Views
    3,898

    Im just curious because i haven't had this issue...

    Im just curious because i haven't had this issue with mine at all.

    Sent from my Nexus 6P using Tapatalk
  3. Replies
    52
    Views
    3,898

    Those temps don't seem hot at all to me. Im...

    Those temps don't seem hot at all to me. Im curious now what temps are on gears

    Sent from my Nexus 6P using Tapatalk
  4. Replies
    311
    Views
    50,700

    My experience from the all aluminum steering...

    My experience from the all aluminum steering racks I've used is they bind up after a few runs. Im not saying this one will but if it does try using the bottom half of the old plastic one on the...
  5. Replies
    52
    Views
    3,898

    This is what I did to my pulley, haven't tried it...

    This is what I did to my pulley, haven't tried it yet been busy. But this won't work for everyone. I use a huge pinion because im running a really low kv motor, 780kv. Also made some aluminum spacer...
  6. Replies
    52
    Views
    3,898

    Same website Gripdog. Just do some searching...

    Same website Gripdog. Just do some searching they're on there.
    And your welcome

    Sent from my Nexus 6P using Tapatalk
  7. Replies
    52
    Views
    3,898

    Yup that's how I've been doing it also. Actually...

    Yup that's how I've been doing it also. Actually I haven't had to reset my belt since I put it on but I was launching 30 ft in the air doing backflips and the motor set screw slipped and loosened up....
  8. Replies
    52
    Views
    3,898

    Problem is my pinion is so big it completely...

    Problem is my pinion is so big it completely covers motor adjustment screws, even going down 10 teeth they would be covered. I'll take pictures when I get home in the morning of the holes I drilled....
  9. Replies
    52
    Views
    3,898

    So just out of curiosity how do you adjust your...

    So just out of curiosity how do you adjust your tension? Im running a 30 pinion on mine and ended up drilling a hole in it to tighten my motor screws but if I ever go smaller im not sure how I'd...
  10. Replies
    38
    Views
    5,186

    Just wanted to share this website with you guys....

    Just wanted to share this website with you guys. US company, shipping only took a couple days and these belts are strong.
    https://shop.polybelt.com/3M-15-15mm-Wide-Belt-Rubber_c59.htm

    Sent from...
  11. Im running a 40/50. Im thinking I want a couple...

    Im running a 40/50. Im thinking I want a couple smaller pinions. My temp is super cool. Of course I haven't run it a whole bunch yet so we'll see

    Sent from my Nexus 6P using Tapatalk
  12. Got to play in the snow for a few...

    Got to play in the snow for a few todayhttps://youtu.be/1Maa0lOl4Ao


    Sent from my Nexus 6P using Tapatalk
  13. Replies
    8
    Views
    608

    I don't see why it won't. I don't use stock motor...

    I don't see why it won't. I don't use stock motor or mount so I can't say for sure and I don't remember what it looks like. But the 4 screws should be more than enough to hold it in place.

    Sent...
  14. Replies
    8
    Views
    608

    I'd recommend to anyone, remove those pins and...

    I'd recommend to anyone, remove those pins and set manually.
    In all honesty they are a great idea. Just way too much difference in company's gears. Not all the same size.

    Sent from my Nexus 6P...
  15. Replies
    3
    Views
    247

    I use red loctite. Let cure over night and if you...

    I use red loctite. Let cure over night and if you need to remove it heat

    Sent from my Nexus 6P using Tapatalk
  16. Replies
    11
    Views
    1,170

    I made my own. Super easy. Couple Velcro straps...

    I made my own. Super easy. Couple Velcro straps and I cut some aluminum pieces.
    Just hit hobby lobby or your lhs https://uploads.tapatalk-cdn.com/20180926/f56a418ca3aa03749cca7fbd5588b101.jpg
    ...
  17. Got mine from Andrew Appleton. Search him on FB....

    Got mine from Andrew Appleton. Search him on FB. Or join Xmaxx belt drive group on fb

    Sent from my Nexus 6P using Tapatalk
  18. Well.... Got about a 45 second run on the belt...

    Well.... Got about a 45 second run on the belt drive and the esc finally gave out. Oh well! Waiting for my replacement now.
    This thing is so darn smooth. I love it already!
    ...
  19. Im on 3 other groups including the Maxx belt...

    Im on 3 other groups including the Maxx belt drive group, and haven't heard of one single issue yet. But, if there's gonna be an issue I guarantee I'll have it! Lol
    I can't wait to get out and do...
  20. Lol. The sound itself is worth it! It's so much...

    Lol. The sound itself is worth it! It's so much smoother and quieter.
    The brace is just off while I work on it and the battery hold downs are junk, I hated them. Just driving on the street doing...
  21. Got the belt drive in and all set up. I cut out...

    Got the belt drive in and all set up.
    I cut out the receiver box and moved my esc down and mounted.https://uploads.tapatalk-cdn.com/20180923/114cce75e23762e5017d62b2843df149.jpg...
  22. Lol. Yes you did. I blame no one but myself. Now...

    Lol. Yes you did. I blame no one but myself. Now I get to spend more money.

    Sent from my Nexus 6P using Tapatalk
  23. So I haven't had a whole bunch of time to mess or...

    So I haven't had a whole bunch of time to mess or drive this lately. Mostly just a couple runs up and down the street. I did take it to the skate park, and of course I popped a cap on my esc.
    Also...
  24. Replies
    4
    Views
    677

    Yup. 6 screws. Be very careful when you pull the...

    Yup. 6 screws. Be very careful when you pull the end caps. You don't want to slide the stator acoss the windings inner wall

    Sent from my Nexus 6P using Tapatalk
  25. Replies
    4
    Views
    677

    I ordered these from Amazon. Perfect fit, a lot...

    I ordered these from Amazon. Perfect fit, a lot nicer than the standard ones.
    6x17x6 mm Deep Groove Ball Bearing,Steel Skateboard Model bearings 606-2RS 606RS 180016 10 PCS Skateboard Bearings...
Results 1 to 25 of 431
Page 1 of 18 1 2 3 4