Search:

Type: Posts; User: grizzly03

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    4
    Views
    45

    That's how my luck goes also. The glow plug...

    That's how my luck goes also. The glow plug leaking was probably the copper washer (gasket). I've had them deform after being tightened/loosened too many times.

    Maybe check the fuel tank cap is...
  2. Replies
    6
    Views
    128

    I would replace what's broken. The mesh doesn't...

    I would replace what's broken. The mesh doesn't look bad, but that spur gear assembly sliding back and forth is not good. It shouldn't be sliding on the input shaft.
  3. v1 vs v2 info: The v2 has a center diff in it...

    v1 vs v2 info: The v2 has a center diff in it along with metal gears.
  4. Replies
    2
    Views
    35

    The correct way to shim a diff is (by trying and...

    The correct way to shim a diff is (by trying and checking) to remove excess play and not by a predetermined amount of shims. To make it easy put one shim on the ring gear side and see how much play...
  5. Replies
    6
    Views
    128

    I'm going to agree with Live2Fish88 about...

    I'm going to agree with Live2Fish88 about something not right with the cushdrive/spur gear. The spur gear should be out farther (more room between it and blue plate). Check the cross pin is in the...
  6. Replies
    4
    Views
    45

    It's certainly possible. The fuel pickup in the...

    It's certainly possible. The fuel pickup in the tank could have a leak. Do you notice air bubbles in the fuel line when it starts acting up? That would be an indicator. Also check your exhaust for...
  7. Replies
    13
    Views
    233

    It's better to have more available power than not...

    It's better to have more available power than not enough. The ESC and motor will only draw what amps they need from the battery, the battery doesn't push the amp current. Stressing a battery as...
  8. It's not a direct swap. The v2.0 input shaft is...

    It's not a direct swap. The v2.0 input shaft is 6mm where the v1 is 5mm.
  9. Thank you. :thumbup:

    Thank you. :thumbup:
  10. Thread: Dust boots

    by grizzly03
    Replies
    33
    Views
    610

    https://uc5428744230b26bbc92871d1fd0.previews.drop...

    https://uc5428744230b26bbc92871d1fd0.previews.dropboxusercontent.com/p/thumb/AA1WeobZE-B4qoArK-4YHwLbldBs_psy183R4fh-MaFHLEOgqDIBj4Dj-3flx9d0eXdqyN8xnNwmukIgIoslSKFXJjpKW5dBiYb30Fm5lHc4QR6bDMvgsmb_Znl...
  11. I found the same problem with mine. Unfortunately...

    I found the same problem with mine. Unfortunately the new plate is also bent slightly. I think it has to do with the stamping process. I adjusted mine by using gear backlash as a guide to set the...
  12. Thread: Trx4 ifs?

    by grizzly03
    Replies
    13
    Views
    195

    This is what I was talking about, Dana 44 TTB. It...

    This is what I was talking about, Dana 44 TTB. It was 4WD and coil spring suspension. Ford 1980-1996. Basically had a universal joint off one side of the differential.
    ...
  13. The steering servo placement and the receiver box...

    The steering servo placement and the receiver box wire opening direction on the TRX4 really don't help at all. You really need a long lead on any servo you choose. I turned my receiver box around for...
  14. Best comment I've read in a long time! :thumbup:

    Best comment I've read in a long time! :thumbup:
  15. Flux, Have you tested out TSM with that servo? I...

    Flux, Have you tested out TSM with that servo? I might end up with that servo instead of getting another DS470BLHV.
  16. Highly impressed. Feels and works like a quality...

    Highly impressed. Feels and works like a quality piece. When they start making them again I'm getting another for my Erevo 2.0

    They only negative I can say, is I needed a servo extension wire to...
  17. Thread: XO-1 motor

    by grizzly03
    Replies
    8
    Views
    138

    I know right! Capable of 8s and a sensored system.

    I know right! Capable of 8s and a sensored system.
  18. Replies
    7
    Views
    271

    If I had an UDR I wouldn't worry about the T8...

    If I had an UDR I wouldn't worry about the T8 Truggy motors. I have a T8 1700kv i'm going to be putting in my Erevo 2.0. I also think it's better than the stock 2200kv motor. (same motor that's in...
  19. Thread: Trx4 ifs?

    by grizzly03
    Replies
    13
    Views
    195

    I think an IFS like what Ford calls the Twin...

    I think an IFS like what Ford calls the Twin Traction Beam front suspension would look awesome! I'd prefer that over the a-arms.
  20. I only have 1 TRX4....

    I only have 1 TRX4. Link:Joined-the-Scale-scene-My-Brushless-Bronco
  21. That's great they are included. They should...

    That's great they are included. They should update their web-page descriptions to help the confusion.
    Of course if they are included without being in the description I'd still call it a "Bonus".
    ...
  22. Replies
    7
    Views
    271

    The Tekin T8 2250Kv motor is their truggy motor....

    The Tekin T8 2250Kv motor is their truggy motor. Same size as the castle 1515 2200kv motor. If it was the buggy motor I would be hesitant. I don't see why the Tekin truggy motors are not comparable...
  23. Replies
    42
    Views
    841

    You should be able to set endpoints with the TQi...

    You should be able to set endpoints with the TQi radio pictured.

    LoL. Can't win them all. Those Big Bore shocks look sharp, it's looking good.
  24. OK. It doesn't help with saying if the OP's combo...

    OK. It doesn't help with saying if the OP's combo comes with one or not. I think this is what they purchased and I don't see a pinion listed in "What's in the box." ...
  25. Replies
    12
    Views
    217

    True. But the OP did say the front...

    True. But the OP did say the front wheels/steering moves back and forth when giving it throttle. Usually out of balance tires wobble all around and not just make the steering turn back and forth....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4