Search:

Type: Posts; User: Decoy Octopus

Search: Search took 0.03 seconds.

  1. Replies
    5
    Views
    588

    Aplastics or on eBay Sent from my VS987 using...

    Aplastics or on eBay

    Sent from my VS987 using Tapatalk
  2. With my 195mm body 0mm front and 6mm rear offset...

    With my 195mm body 0mm front and 6mm rear offset wheels fit. 3mm in the front is ok, 0 is perfect.
  3. Replies
    5
    Views
    588

    The inside, my plan is to "dip" the outside clear...

    The inside, my plan is to "dip" the outside clear then peel the inside and repaint. Most of the decals on the mustang are on the inside too, just printed in reverse.

    I mainly want to redo the...
  4. Replies
    5
    Views
    588

    Built it more for handling around a parking...

    Built it more for handling around a parking lot.... my alternate mounting for the GPM arms. Front braces are lower to clear 0 offset wheels (Or the foams everyone uses). Rear, I used short ball ends...
  5. Replies
    5
    Views
    588

    Decoy's Ford GT and Mustang

    Just finished the GT body, the Fox Body I drove around last year and has a little wear. It's getting fresh paint and custom sticker job, they're both done with Plasti...
  6. Replies
    13
    Views
    2,698

    I did redid the shocks just like this and got...

    I did redid the shocks just like this and got TiNi shafts and after driving it a few times I can say it really soaks up the bumps. It's fun to watch the suspension work; also I don't get as many...
  7. Replies
    3
    Views
    549

    It's a design flaw I think, the only thing that...

    It's a design flaw I think, the only thing that keeps the shaft from walking is the press fit of the spur and bearing. It's not an insanely tight fit to begin with, so it works loose eventually. My...
  8. Replies
    19
    Views
    1,964

    Looks like the GT mounts if you compare the rear...

    Looks like the GT mounts if you compare the rear body holes on the vette and GT. The GT mounts are different from the Mustang.
  9. Replies
    4
    Views
    615

    The install was exactly how I imagined, but I...

    The install was exactly how I imagined, but I learned that the little pin is included, which makes it a win. The product pictures never show the pin.

    Now knowing that I don't need to reuse any...
  10. Thread: Shocks

    by Decoy Octopus
    Replies
    4
    Views
    640

    Looks to be 59mm eye to eye.

    Looks to be 59mm eye to eye.
  11. Replies
    15
    Views
    1,277

    Differences chassis wise... Steel driveshaft...

    Differences chassis wise...

    Steel driveshaft
    Blue adjustment nut on servo saver, otherwise same servo saver and bell crank with bushings.
    Steel links instead of the plastic camber/tie rod links...
  12. Replies
    19
    Views
    1,964

    The 'vette is pretty sweet... I'm not even a...

    The 'vette is pretty sweet...

    I'm not even a "Mopar guy", but I want a true 200mm Challenger body. There's a lack of them out there, save for the generic 190mm and the Kyosho that's too big....
  13. Replies
    4
    Views
    1,267

    I know this is older, but I sanded my Savox...

    I know this is older, but I sanded my Savox SC-1258tg case down with a dremel and haven't had a problem all summer. Be careful how much you sand off if you do it, there's a fair bit of meat to sand...
Results 1 to 13 of 14