Search:

Type: Posts; User: gmoney82186

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1,591
    Views
    237,908

    What happened??

    What happened??
  2. Replies
    5
    Views
    256

    So I believe I found the problem! I emailed...

    So I believe I found the problem! I emailed Traxxas and they said it could be temp sensor. Swapped it and I have solid green and my initial tests show the low end throttle issue is fixed! I’ll get a...
  3. Replies
    5
    Views
    256

    Will do… I am hoping this will fix my issue where...

    Will do… I am hoping this will fix my issue where the truck is super jumpy at minimal throttle. The best way to describe it, is I am now nervous to drive it anywhere around my kids even at the lowest...
  4. Replies
    5
    Views
    256

    Are the batteries in the car fully charged? - Yes...

    Are the batteries in the car fully charged? - Yes

    Is there water inside of the receiver box? - No, not a drop...
  5. Replies
    5
    Views
    256

    Receiver Blinking Red Fast

    Hey guys,

    Long time since I’ve posted in the Maxx section..

    My TQI receiver is blinking red (fast blink). It still binds to my radio, but even if I re bind it or swap to different radio it...
  6. Replies
    7
    Views
    340

    Thanks guys!

    Thanks guys!
  7. Replies
    7
    Views
    340

    Yes, but I found out even if you’re ESC’s...

    Yes, but I found out even if you’re ESC’s internal BEC can handle it, if you’re receiver is rated at 6.0v and you go higher (7.4) you’ll fry your receiver.

    So it sounds like I’m good if I do a...
  8. Replies
    7
    Views
    340

    2255 Servo with different ESC

    Looking for someone smarter than me on this ;).

    So the 2255 Traxxas servo is rated at 400oz @ 6v. Right now I’m running this with the Traxxas BEC.

    My question is if I upgrade to brushless and...
  9. Replies
    2
    Views
    298

    I have STRC mounts I used. What I was wanting is...

    I have STRC mounts I used. What I was wanting is something that would allow me to keep the fender on the chassis. Looking at it, it would have to be a full fender/mount.
    ...
  10. Replies
    5
    Views
    580

    You can use aftermarket shock towers.. ...

    You can use aftermarket shock towers..

    https://uploads.tapatalk-cdn.com/20190710/8e5e758eab81c6eae53c4c7e03013403.jpg
  11. Replies
    2
    Views
    298

    Blazer aftermarket shock towers

    Hi all! Been a while...

    Got a TRX 4 Blazer and loving it. Upgrading to Hitec 7954SH servo and Traxxas BEC..

    Now to my problem. I bought some STRC aluminum shock mounts front and rear with my...
  12. Gearing is totally your preference and doesn’t...

    Gearing is totally your preference and doesn’t affect mesh. If you got a 48 pitch pinion that was why it didn’t match up
  13. I answered your question on the other thread. The...

    I answered your question on the other thread. The stock spur is mod 0.5. I drilled the stock Traxxas pinion (carefully and took a little while) and still use it. Also ordered a 13t pinion from a 18T...
  14. Replies
    3
    Views
    517

    I drilled out the stock pinion with a numbered...

    I drilled out the stock pinion with a numbered bit. The spur is 0.5 mod so I ordered a pinion from a TA 18T
  15. Replies
    2
    Views
    379

    Max 6 Throttle Sensitive

    Hey guys, been a while, hope all is well!

    My XMaxx is super touchy with the throttle. To the point where I’m nervous to drive it around my kids. I’ve re calibrated my Hobbywing Max 6 but it still...
  16. Replies
    4
    Views
    526

    Yes! I was right... this forum is hardcore when...

    Yes! I was right... this forum is hardcore when it comes to, well anything, so I knew that would be an issue..
  17. Replies
    4
    Views
    526

    I think they think the replies weren’t adding...

    I think they think the replies weren’t adding much to the thread LOL. Running the HR Mount because even with setting my mesh manually and torquing down the bolts (with the aluminum motor mount...
  18. Replies
    4
    Views
    526

    Hot Racing Motor Mount

    Hey guys, anyone have any experience with the HR motor mount?

    I ordered one in hopes that it would help make setting my gear much easier, and stay in place better. I will be sticking with the...
  19. Replies
    3
    Views
    517

    My “sons” QuicRun Teton

    So I’ve been wanting a Teton for a while and finally convinced the wife my 1.5 year old needed it. Swapped to Hobbywing QuicRun BL system, Savox 0262 servo, XT60’s, Venom Lipo, and LaTrax Aluminum...
  20. Replies
    2
    Views
    212

    Nice! Let me know how you like your bell crank...

    Nice! Let me know how you like your bell crank from them.. thinking about getting it.
  21. Replies
    22
    Views
    892

    IMO you should check everything out “out of the...

    IMO you should check everything out “out of the box”... too many early Monday and late Friday RTR’s come out with some slight issues
  22. Replies
    3
    Views
    701

    Nice! What BL system did you go with?

    Nice! What BL system did you go with?
  23. Replies
    2
    Views
    333

    I was looking into these for an upgrade down the...

    I was looking into these for an upgrade down the road.. The stock ones are OK, but I am not a fan of Traxxas steel...
  24. Dude! Looks fantastic and especially for first...

    Dude! Looks fantastic and especially for first time. I’m not a fan of painting, but I have done a couple bodies under protest. I’m so happy the Bash armor came out so I can be lazy and not paint!
  25. Replies
    11
    Views
    514

    Hmmmmm… I may just have to get some and try them...

    Hmmmmm… I may just have to get some and try them out. I like the stock wheels because of the air control due to them expanding.
Results 1 to 25 of 195
Page 1 of 8 1 2 3 4