Search:

Type: Posts; User: RICK DIZZLE

Page 1 of 20 1 2 3 4

Search: Search took 0.60 seconds.

  1. Dude! I really like that Ram body!!!

    Dude! I really like that Ram body!!!
  2. Replies
    7
    Views
    260

    You could always use Easy Off oven cleaner. Put...

    You could always use Easy Off oven cleaner. Put the push rods on a baking tray, ensure they have no plastic ends on them. Spray with Easy Off and let sit. Do this a couple times and boom! All of the...
  3. Thanks for the replies! I always store my lipos...

    Thanks for the replies! I always store my lipos in my home in a fire sack inside vented ammo cans. That way I can keep their temperature ambient and not allow them to just sit through hot and cold...
  4. Storing RCs in the garage...opinions wanted.

    I have come to a point in my RC collection that I may need to start storing RCs in the garage. I live in southern AZ so we see low temps in the upper 20įs and highs in the high 90įs. Obviously I...
  5. Will be a great investment. All you need is the...

    Will be a great investment. All you need is the motor temp sensor and the mount...everything else you need is built in already! Part #s TRA6521 and TRA6535.
  6. The fans are not water proof..safest bet, just...

    The fans are not water proof..safest bet, just pull them off real quick if your going to hose the truck down. I would recommend if your not planning on getting the link module and app along with a...
  7. Replies
    2
    Views
    251

    Stay away from self righting function unless you...

    Stay away from self righting function unless you like rebuilding diffs in your down time...
  8. Replies
    15
    Views
    1,243

    If you have the ability..both...if not...start...

    If you have the ability..both...if not...start with Chassis Brace then do straps.

    Sent from my SM-G955U using Tapatalk
  9. Replies
    2
    Views
    241

    +1 on the above

    +1 on the above
  10. Replies
    1
    Views
    340

    I use the RPM monster camber gauge. You can flip...

    I use the RPM monster camber gauge. You can flip it on its side with and with a 2x4 as a square set your alignment too. Been doing it in all my rigs for years!
    ...
  11. Call Traxxas......

    Call Traxxas......
  12. Replies
    3
    Views
    503

    Lololol! Love it! Too funny! Happy Thanksgiving...

    Lololol! Love it! Too funny! Happy Thanksgiving everyone!
  13. Replies
    5
    Views
    392

    Yeah just spur and pinion, you are correct. I am...

    Yeah just spur and pinion, you are correct. I am unsure how big the Hoons are height wise vs the GRPs. You can start 20/46 and see how it handles and responds. Just watch your ESC and motor temps....
  14. Replies
    5
    Views
    392

    You will have to regear it as you drop tire size....

    You will have to regear it as you drop tire size. I run 1/5th GRPs on my street truck for street racing. If you run stock gears with smaller tires you will be far slower then stock set up....
  15. I wired my fans together to one plug. Then you...

    I wired my fans together to one plug. Then you just plug them directly into a 2s receiver battery. Just be disciplined in checking your voltage between runs. I usually just recharge the receiver pack...
  16. The fans should spin relatively free with just a...

    The fans should spin relatively free with just a tad of resistance...I never run any of my fans off of my receivers. I run all my fan set ups off of a 2s reciever lipo pack, stand alone. On my basher...
  17. Thread: Erevo GPS

    by RICK DIZZLE
    Replies
    1
    Views
    220

    I went the cheaper route I can use on a my rigs....

    I went the cheaper route I can use on a my rigs. A small GPS I can strap on to any vehicle in run. Its the SkyRC GPS. Works great is just about dead on.
  18. Replies
    1
    Views
    272

    Put it on a vise and crank it closed. JUST...

    Put it on a vise and crank it closed. JUST KIDDING!!!! LOL! Post some pics and we can try to give you some actual ideas.:thumbup:
  19. Replies
    19
    Views
    1,124

    I wish EMperformance would make us some titanium...

    I wish EMperformance would make us some titanium drive cups! Boom! Issue fixed. They are only $20 a set for stock...so not to worried. Just be nice to not have to flop them...then replace.
  20. Replies
    19
    Views
    1,124

    Only thing I've ever seen, my brother split a...

    Only thing I've ever seen, my brother split a drive cup in two on a bash session...weirdest thing we have ever experienced driveline wise. Pretty sure it was a production anomaly. Otherwise just...
  21. Can you take a pic from the top down like this?...

    Can you take a pic from the top down like this? Curious to see your shocks and preload along with the position of your rockers. Wonder if its a bent rocker...
  22. Replies
    9
    Views
    940

    Dude those things are nice, and respective to...

    Dude those things are nice, and respective to what some of the RC companies charge for bags that size...good pricing as well!
  23. Did you happen to use the dreaded self-right...

    Did you happen to use the dreaded self-right feature? Open the pinion/spur cover and see if the motor worked itself a tad loose and maybe you ate a gear there. Hopefully easy and we can get you up...
  24. Yeah I broke several Yeah plastic fans landing on...

    Yeah I broke several Yeah plastic fans landing on my lid from high heights, even bent several aluminum housings. I have run the R1s on my street truck for about a year with no issue. But it doesnt...
  25. I run R1 fans on my rigs now. They move much more...

    I run R1 fans on my rigs now. They move much more air but are only plastic cases. They are quiet fans and move a ton of air. Got sick of trashing the Yeah racing fans. R1s have been my best path thus...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4