Search:

Type: Posts; User: Flux Capacitor

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. I'll tell you what though grizzly, you got to...

    I'll tell you what though grizzly, you got to admit at least there is now a company that realizes that a truck of this magnitude needed a third bearing for the front and rears. When I first got my...
  2. I'm just going to say that it will be a 50/50...

    I'm just going to say that it will be a 50/50 gamble. To be more honest, I'm going to say more like 70/30, meaning there is a 70% chance that an issue will arise using a 2085X servo because it is not...
  3. If I recall correctly, the new firmware updates...

    If I recall correctly, the new firmware updates affected whether or not the V/T slot had the sensor plugged in. If you had a 6533 TSM receiver fully updated and the motor temperature sensor wire was...
  4. This is somewhat intriguing to hear considering...

    This is somewhat intriguing to hear considering this problem is evident with the VXL-8S models as well. So......if I am understanding correctly that you have a VXL-6S ESC with this issue, that would...
  5. Replies
    7
    Views
    174

    You're Welcome! The video isn't long, but it...

    You're Welcome!

    The video isn't long, but it sure gets to the point of what is happening. I could have made a ten minute video of the same thing to show that it happens over and over again.

    Now...
  6. Replies
    7
    Views
    174

    The thread HERE...

    The thread HERE outlines your issue.

    Video is courtesy of the member varunaX

    VIDEO

    Also, interestingly enough, I had a THREAD HERE that started out as what I thought was a calibration issue...
  7. The output gear is available HERE...

    The output gear is available HERE

    Yes, I confirmed the output gear is absent in your link, plus that set is $20 more than the one I linked and missing the piece you need!

    If you are asking if...
  8. Replies
    15
    Views
    459

    Thanks for the video! I was having video and...

    Thanks for the video!

    I was having video and audio problems after a windows update, but finally got it sorted out and was able to watch your video.

    You have nice throttle control doing your...
  9. Replies
    15
    Views
    459

    That is good to hear! I almost mercifully...

    That is good to hear!

    I almost mercifully forgot that there are those that can support their local hobby shops.

    I wish I could say the same, unfortunately mine are not local (at least 80 miles...
  10. Replies
    15
    Views
    459

    That's pretty good. Two days between your post of...

    That's pretty good. Two days between your post of hoping to get one and the post of actually owning one!

    Wish I knew the shipping people you do; of course you probably knew it was on the way!
    ...
  11. Just to add to what you are pointing out - it...

    Just to add to what you are pointing out - it isn't just the pinion walking that is causing all the problems. To clarify, I will stress the importance of the pin mesh system. When a person manually...
  12. But you are missing the part that even if the...

    But you are missing the part that even if the pinion shaft hole was shaped like the motor shaft, the pinion still has the ability to walk up or down the motor shaft when the pinion grub screw loosens...
  13. In that video he mentioned also that "reverse...

    In that video he mentioned also that "reverse instantly" was an issue. He said: "Could you imagine people bumping the trigger by accident and just blowing the gear every time?"

    That sounds like...
  14. Replies
    5
    Views
    317

    The thread was HERE....

    The thread was HERE.

    I tried to make the high density foam from Foamma work in the stock tires and the stock tires being re-glued just couldn't handle the heavier foams. The tires just started...
  15. Very good question that proves a point my friend....

    Very good question that proves a point my friend.

    There is absolutely nothing wrong with the pin mesh system and I'm willing to bet that those that blamed the pin mesh system for their spur/pinion...
  16. Replies
    11
    Views
    506

    I saw they used an old driveshaft in that reddit...

    I saw they used an old driveshaft in that reddit link you posted but what is that piece you used?

    I like what you did and hope it works out for you.
  17. Thank you for posting the video. I wanted so...

    Thank you for posting the video. I wanted so badly to post a full video of this very problem but was so frustrated and angry with what was happening with these servos that I gave up too soon.

    I...
  18. Replies
    23
    Views
    911

    As grizzly pointed out, there are no specific...

    As grizzly pointed out, there are no specific instructions in the manual to suggest the servo saver is adjustable. So, I tightened mine down to where all pieces are flush. The design itself suggests...
  19. Replies
    23
    Views
    911

    Click the blue underlined word "THREAD" below and...

    Click the blue underlined word "THREAD" below and have a good read as all the pictures are still active in the thread.

    This THREAD outlines extensively what I thought was a servo saver problem and...
  20. Replies
    21
    Views
    14,410

    That is the problem right there. The EVX ESC is...

    That is the problem right there. The EVX ESC is rated at 14.4 volts so when you were hooking up your two 7.4v (2S) LiPo's, an over current was detected by the EVX ESC and disabled forward and reverse...
  21. I'm not even sure if the OP reached out to...

    I'm not even sure if the OP reached out to customer support regarding this (oh, wait a minute; yes he did and was told they are all like that)--Mine isn't!.......at any rate;

    The sad thing is,...
  22. Also, another thing I wanted to point out other...

    Also, another thing I wanted to point out other than someone being cross-eyed in the process that produced misaligned final results on the body, is that on every production line whether it is manual...
  23. I do believe we both agree and that we arrived at...

    I do believe we both agree and that we arrived at the same conclusion in a different approach of how it is happening. In other words, I may see the glass as half full and you may see it as half...
  24. Either way, someone was cross-eyed in the process...

    Either way, someone was cross-eyed in the process and I'm sure they will find a way to blame machines rather than humans so someone can still keep their job.

    Regardless, it is still someones job...
  25. :lol: Well you did ask nicely for help in the...

    :lol:

    Well you did ask nicely for help in the posting images department; so I think you are guilty as charged!

    :lol:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4