Search:

Type: Posts; User: MECHANIC77

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. The clutch cover is a plastic cover who cover the...

    The clutch cover is a plastic cover who cover the pinion and the spur gear but I can see on your vidéos that this part is missing.
  2. By what you described and by the symptomatic...

    By what you described and by the symptomatic behavior of what it is possible to observe, I'm almost sure that the top gear lock pin is broken and a good way to make sure of it, is to remove the...
  3. Replies
    21
    Views
    2,481

    There's no need to put the ESC in race mode to...

    There's no need to put the ESC in race mode to correct the problem that it reverse by itself and when we do this we lose the same percentage of power to the forward motion that we have in reverse...
  4. The problem is that the seven blades fan unit has...

    The problem is that the seven blades fan unit has thinner and less wider blades than the five blades fan and it tends to break easily during impact. Also with a five blades unit it will be more...
  5. I'm not a great fan of plastic fan unit because...

    I'm not a great fan of plastic fan unit because it does not absorb and transfer any heat from the motor, in my opinion it better have an aluminum unit which will act like a heat sink and will work in...
  6. Replies
    6
    Views
    218

    Ok now I understand, he want to know if is it...

    Ok now I understand, he want to know if is it normal to have bearings in the transmision instead of bushings, also after some verifications, I have to admit that Fast Eddy’s does not made shielded...
  7. Replies
    6
    Views
    218

    By what you explain, I guess you have ordered a...

    By what you explain, I guess you have ordered a set of shielded bearing instead of the sealed ones and if it's the case, the only problem is that the sand and dust will passe through the shield at...
  8. Thread: Spur gear

    by MECHANIC77
    Replies
    1
    Views
    316

    Sometimes people remove the paper before...

    Sometimes people remove the paper before tightening the top screw and usually the motor backs up a little bit, the best way to accomplish this is to keep the paper in place, and when tightening the...
  9. Replies
    14
    Views
    772

    The problem could be a number of things and I...

    The problem could be a number of things and I need to proceed by elimination to find it, so can you show me a photo or point me on a link of which driving shafts you are running on. Also it's...
  10. Replies
    14
    Views
    772

    Sometimes the wheels are so out of balance that...

    Sometimes the wheels are so out of balance that the bearings can't handle the vibration and / or after a crash it's possible that the wheels turn false and this causes too much stress on the...
  11. Replies
    10
    Views
    991

    The Velineon ESC thermal cutoff temperature value...

    The Velineon ESC thermal cutoff temperature value should be at the lowest 185 F° and at the highest 195 F° depending on the model version of the ESC.
  12. Replies
    6
    Views
    473

    Thanks for bringing this to my attention and I...

    Thanks for bringing this to my attention and I noticed that I explained myself badly and I should have written: but I really doubt it would be possible to reach a speed of (41-43mph) on a 2s lipo...
  13. Replies
    6
    Views
    473

    Interesting theory above and in certain...

    Interesting theory above and in certain circumstances it would be representative of the reality. However if Traxxas claim a speed of 40 mph on their Rustler speed chart (with the 17 / 54 gearing and...
  14. Replies
    1
    Views
    140

    I'm sorry to tell you that you're in the wrong...

    I'm sorry to tell you that you're in the wrong Forum and actually a Rustler 4x4 Forum exist, which has an active thread on the subject.



    I hope this will help....
  15. Replies
    1
    Views
    240

    As far as I know, there's only one company who...

    As far as I know, there's only one company who makes wheel off set adapter but the stock availability is limited, so check for other colors to see if they have the length that you're looking for....
  16. Replies
    6
    Views
    296

    The hex drive is 12mm with a maximum axle...

    The hex drive is 12mm with a maximum axle diameter of 0.196″ (5mm) the Mohawk tire will fit directly on the wheel and they will fit right on your Bantit.
  17. Replies
    6
    Views
    296

    Oups I'm sorry, I have mingled the front set with...

    Oups I'm sorry, I have mingled the front set with the wide wheelbase one, which is usually used with a wider wheelbase vehicle, (like the Slash is) so they are closer from the chassis than the front...
  18. Replies
    6
    Views
    296

    RPM makes strong and lightweight rims, their...

    RPM makes strong and lightweight rims, their nylon base plastic technology is really good, they say they are indestructible and I have those rims with a set of Badland mounted on it, so I can't...
  19. Replies
    6
    Views
    237

    I agree that a 2.2 setup is better for the bandit...

    I agree that a 2.2 setup is better for the bandit but IMO with paddle tires the handling is so weak that it don't really matter, however with a 2.2 setup the front handling will be a little better...
  20. Replies
    6
    Views
    237

    There are not several companies that make paddle...

    There are not several companies that make paddle tires, however the most populars are Traxxas and Pro-line, those companies offers the most performing paddle tires on the market.



    Traxxas...
  21. Replies
    10
    Views
    991

    The cooling unit look like good but I'm sure that...

    The cooling unit look like good but I'm sure that the cooling fins will interfere with the driving shaft, so it's possible to cut off a part of the cooling jaket with a Dremel but if you can find a...
  22. Replies
    10
    Views
    991

    I just made an update and I hope it will respond...

    I just made an update and I hope it will respond to your question and there is no motor overheat protection on the Velineon system.
  23. Replies
    10
    Views
    991

    When we run 3s lipos we need the use of a ESC...

    When we run 3s lipos we need the use of a ESC fan, otherwise the ESC will set into thermal protection cut off, so there are three options, (1) it's possible to buy the Velineon fan unit but the...
  24. Replies
    13
    Views
    841

    The only fonction of the swivel ball used in the...

    The only fonction of the swivel ball used in the stock plastic cap is to provide a left and right motion of the cap during the suspension compression and releasing movement, therefore there's no need...
  25. Replies
    13
    Views
    841

    There are no way to fit the swivel ball inside of...

    There are no way to fit the swivel ball inside of any aluminum cap hole, so you have two solutions, (1) it's possible to buy parts number (3642X) and (2746) then you will have all the necessary...
Results 1 to 25 of 447
Page 1 of 18 1 2 3 4