Search:

Type: Posts; User: grizzly03

Page 1 of 13 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    6
    Views
    139

    I do know that the plastic corrugated sheets...

    I do know that the plastic corrugated sheets (similar as the signs) can hold a lot of weight. They use the material for packaging. Basically a cube box that is collapsible and used in tractor...
  2. Replies
    6
    Views
    514

    Look at each vehicles' exploded view. I don't own...

    Look at each vehicles' exploded view. I don't own a slash. So I cannot comment on what the parts look like for swapping. I have a Jato and it is a one off setup. Meaning it would take a lot of custom...
  3. Replies
    41
    Views
    2,016

    You don't need to plug in the transmission...

    You don't need to plug in the transmission sensor. The sensor tells the opti-drive module when it is ok to shift. Without having the opti-drive module there's no need for the sensor.
  4. Replies
    69
    Views
    4,299

    Thanks. Never heard someone describe an engine as...

    Thanks. Never heard someone describe an engine as one. I use piston port(piston only), reed valve(check valve), or rotary valve(adjustable) based on the intake type when I describe.

    I just...
  5. If you never had an RC vehicle before or have...

    If you never had an RC vehicle before or have battery knowledge I would stick with NiMh batteries. Lipo batteries require more care and maintenance. NiMh batteries are more forgiving and cheaper. Buy...
  6. Replies
    3
    Views
    264

    Back before there were waterproof receiver boxes...

    Back before there were waterproof receiver boxes I would use plain ole balloons to protect them. Zip-tied the end where the wires came out. Worked good for water splashes.
  7. Replies
    69
    Views
    4,299

    Look at what I found on youtube:...

    Look at what I found on youtube: https://www.youtube.com/watch?v=A19b56_AR8E.

    Nitronaught, I'm not sure what you mean by blowby engine? These engines are a rotary valve type of 2-stroke.

    Bob,...
  8. Replies
    7
    Views
    492

    I would give the truck a quick going over....

    I would give the truck a quick going over. Checking for anything loose. I purchased a Jato over the summer and the slipper was loose and wheel alignment was way off right from the factory. These...
  9. There is one for the 1/16 erevo part 7185...

    There is one for the 1/16 erevo part 7185. It doesn't look to bad for bashing as it installs leds in the included bumpers. Should hold up unless you rip off bumpers.
  10. Replies
    69
    Views
    4,299

    Any progress? I would like to see a video of this...

    Any progress? I would like to see a video of this thing running as I'm having a harder time believing this engine conversion is working out as your describing. I know converting a glow engine to...
  11. Replies
    69
    Views
    4,299

    If you put ceramic on the cylinder head, how...

    If you put ceramic on the cylinder head, how would the head cool the engine if it wasn't allowed to absorb heat? How hot does the engine get? Could you be running too lean? I know that air/fuel...
  12. Replies
    6
    Views
    514

    Crackles what is your goal. Do you just want an...

    Crackles what is your goal. Do you just want an aluminum chassis or do you want to make a new vehicle?
    The rustler and bandit are different than the jato. The parts you have are not a direct swap....
  13. Replies
    69
    Views
    4,299

    Impressive!! Nice job on mounting. I had a hard...

    Impressive!! Nice job on mounting. I had a hard time seeing the carb mounted. I don't think ceramic coating would help with this style motor. These engines don't have rings and require parts to...
  14. Replies
    5
    Views
    249

    If it doesn't fit one way try turning the pack...

    If it doesn't fit one way try turning the pack sideways.
  15. Replies
    69
    Views
    4,299

    You changed crank timing not port timing. Why...

    You changed crank timing not port timing. Why mess with any timing (crank or port) if you haven't gotten the motor to run more than a minute or so? i would have thought it would have been easier to...
  16. Replies
    5
    Views
    249

    What battery do you have?

    What battery do you have?
  17. Replies
    30
    Views
    1,062

    Sounds like someone is Trolling. :thumbdown:

    Sounds like someone is Trolling. :thumbdown:
  18. Replies
    30
    Views
    1,062

    I don't know about catching fire. Sounds like you...

    I don't know about catching fire. Sounds like you heard some Tall Tales. The stock servo did go bad on me and I replaced it with the 2085x.
  19. I wonder if you could make something and fit it...

    I wonder if you could make something and fit it on the chassis bottom like the t-bone racing skid plates. (I have no idea how strong their material is, never used any of their products). Some kind of...
  20. Looks like an awesome place to run, wish I had an...

    Looks like an awesome place to run, wish I had an area like that! :thumbup:
    I wouldn't feel bad about breaking any parts. You can hear your revo slamming the ground. LOL
    Maybe try P3 rocker setup....
  21. +1 on what are your settings at now. Also check...

    +1 on what are your settings at now.
    Also check your exhaust for any leaks. Side note; you had good tuning on your slash.
    What changed? :confused: New vehicle? Used engine?
  22. Replies
    41
    Views
    2,016

    Yes. Unplug the opti-drive from ch 2 and ch 3....

    Yes. Unplug the opti-drive from ch 2 and ch 3. Then plug your throttle servo directly to ch 2 and your reverse servo directly to ch 3 on the receiver. Just remember to stop before shifting into...
  23. You must get some serious air! I never tried...

    You must get some serious air! I never tried running in a skatepark. Must be fun! :woot:
    When you switched from v1 to v2 did you go heavier on the suspension?(springs or oil?)
    Just an idea: Try...
  24. Never seen one of these gadgets. Looks like it...

    Never seen one of these gadgets. Looks like it would/could be useful for me. How do they attach? Magnetic?
  25. Replies
    41
    Views
    2,016

    Just wanted to let you know what the stock setup...

    Just wanted to let you know what the stock setup is, so you wouldn't be surprised by the difference.
    Have you tried bypassing the opti-drive to see if it helps with "radio issues". Also make sure...
Results 1 to 25 of 311
Page 1 of 13 1 2 3 4