Search:

Type: Posts; User: Kpowell911

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    17
    Views
    690

    I didnt mean it like that. I have zero interest...

    I didnt mean it like that. I have zero interest in speed runs. Im a basher, and wondered if Xo-1 Shafts were a bad choice for my basher
  2. Replies
    17
    Views
    690

    That could be a possibility to be fair. When I...

    That could be a possibility to be fair.

    When I say this truck was pre owned, It was built up as a shelf queen. I was the first to even lay it on a piece of ground haha.

    Its done now, fixed and...
  3. Replies
    16
    Views
    778

    That snow has gone now, probabaly wont see it...

    That snow has gone now, probabaly wont see it again for a year or so, not worth it in the UK haha
  4. Replies
    8
    Views
    5,440

    All Im saying. First of all what are the import...

    All Im saying. First of all what are the import laws in terms of custom charges from the US in NL? Will you be charged? If youre going to be charged €30 import charges, its not really worth saving...
  5. Replies
    8
    Views
    5,440

    I'm in the UK and used them for years. However,...

    I'm in the UK and used them for years. However, Im not sure what the laws are in importing from the US to the NL, just bare in mind you may have to pay a customs charge.

    Also, bare in mind youre...
  6. Replies
    29
    Views
    819

    Just double checked mine and youre right! That...

    Just double checked mine and youre right! That used to looking at 8mm shafts from my Xmaxx I thought it was a 3.2
  7. Replies
    16
    Views
    778

    https://i.imgur.com/qPNUkJ5.jpg :)

    https://i.imgur.com/qPNUkJ5.jpg

    :)
  8. Replies
    29
    Views
    819

    The SCT comes with an esc mounting plate Also,...

    The SCT comes with an esc mounting plate

    Also, my 3660 has a 3.2mm shaft so can use regular pinions?
  9. Replies
    17
    Views
    690

    Let me first of all say this isn't my first R/C....

    Let me first of all say this isn't my first R/C. Ive had Traxxas vehicles since they were kits with MSC's and unpainted shells. This is probably my 5th or 6th Slash 4x4 variant. Im aware R/C's break,...
  10. Replies
    17
    Views
    690

    Broken XO-1 axle very easily

    Hello, I purchased a Slash/Rustler 4x4 that someone had built up and never used. The reason I brought this exact model was because it had some very desireable and expensive modifications. Mainly,...
  11. Basically this is what happened: ...

    Basically this is what happened:

    https://i.imgur.com/8RukVMz.jpg
  12. Traxxas XO-1 Shafts - Broken witin 10 minutes!

    Hello, I purchased a Rustler 4x4 that someone had built up and never used. The reason I brought this exact model was because it had some very desireable and expensive modifications. Mainly, XO-1...
  13. Replies
    16
    Views
    1,094

    When does this get released?

    When does this get released?
  14. Replies
    16
    Views
    778

    lol, less than 1 minute into my first run ...

    lol, less than 1 minute into my first run

    https://i.imgur.com/DKRwxSV.jpeg

    My fault, I'm an idiot
  15. Replies
    16
    Views
    778

    Ive never liked T Bone stuff, it just looked so...

    Ive never liked T Bone stuff, it just looked so cheap and home made. I appreciate it works, and Ive not looked at their products for a while but still.

    I'm running a centre diff, is this stock on...
  16. Replies
    4
    Views
    434

    That 4000kv is going to be around the same...

    That 4000kv is going to be around the same performance as the stock VXL, but run warmer and will be limited gearing. I wouldnt use it, 4000kv is too high for off road
  17. Replies
    8
    Views
    554

    Crisis over. As you can see the difference is the...

    Crisis over. As you can see the difference is the lower corner


    https://i.imgur.com/TaKPcFF.jpg
  18. Replies
    16
    Views
    778

    Also, I've converted this off the top of my...

    Also, I've converted this off the top of my head...... IS this right for the rear end/wheely bar? Doesn't seem too secure?


    https://i.imgur.com/dUQ8NZH.jpg
  19. Replies
    16
    Views
    778

    After a few hours googling and downloading...

    After a few hours googling and downloading exploded diagrams..... I confidently found the new correct motor mount. An aftermarket one was an option so I went for that. It wasn't cheap but was in...
  20. Replies
    16
    Views
    778

    Slash 4x4 to Rustler 4x4

    Hello, I'm sure a fair few of you know me, I've been on here since 2009, and into the hobby around 25 years..... However, at the end of 2019, I sold up. For Good. Even down to my tools. I took down...
  21. Replies
    8
    Views
    554

    Ive found it in stock at Wheelspin, but dont know...

    Ive found it in stock at Wheelspin, but dont know if its what I need?
  22. Replies
    8
    Views
    554

    Hmmm. Not sure what to do as I dont want to start...

    Hmmm. Not sure what to do as I dont want to start grinding things

    Hopefully I can obtain 7460A or 7460R easily enough in the UK.

    When did this change happen does anyone know? My Rustler...
  23. Thread: Motor mount

    by Kpowell911
    Replies
    9
    Views
    466

    Thank you for this, Im having a nightmare!

    Thank you for this, Im having a nightmare!
  24. Replies
    8
    Views
    554

    7460 vs 7460A/R

    Hello, Im in the process of converting a Skash 4x4 to a Rustler 4x4. I believe I have everything, however the motor mount from the Slash 4x4 I have (LCG) doesn't line up.

    It wont fit behind the...
  25. Thread: Motor mount

    by Kpowell911
    Replies
    9
    Views
    466

    Thanks. My rustler isnt here yet so cant check

    Thanks. My rustler isnt here yet so cant check
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4