Search:

Type: Posts; User: slo-n-lo

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    254

    thanks for the link.. guess i didnt look hard...

    thanks for the link.. guess i didnt look hard enough :lol:
  2. Replies
    6
    Views
    254

    need new carb..

    found out my carb is stripped where the HSN needle holder screws in. cant seem to find a part number for the carb body or even the whole assy.
    how do i go about getting a new carb? is there any...
  3. Replies
    16
    Views
    514

    ???is there a fuel tank issue? what about the...

    ???is there a fuel tank issue? what about the stock tank makes the engine run lean???
  4. Replies
    20
    Views
    343

    if you pull the bearing there will be a bearing...

    if you pull the bearing there will be a bearing code or number stamped somewhere on the outer race. write that down and look these guys up. (Pervis bearing) located in Dallas Texas.
    they sell these...
  5. Replies
    11
    Views
    450

    clear finger nail polish works well also. holds...

    clear finger nail polish works well also. holds good and tight but alot more giving when the screws need removing.
  6. Replies
    17
    Views
    473

    very nice!

    very nice!
  7. Replies
    49
    Views
    2,499

    looks more like the associated monster truck to...

    looks more like the associated monster truck to me..
  8. Replies
    8
    Views
    443

    the slipper clutch will make kind of a whistling...

    the slipper clutch will make kind of a whistling or chirping sound upon heavy accel.
  9. Replies
    14
    Views
    363

    looks like you have either a bent shock shaft or...

    looks like you have either a bent shock shaft or a broken shock dampener plate.:eek:
  10. Replies
    5
    Views
    277

    DOH!!!! it was the pillow ball retainer. guess i...

    DOH!!!! it was the pillow ball retainer. guess i didnt see it in there. man my eyesight is starting to go. old age blows!!!! :lol: :lol: :lol: :rolleyes:
  11. Replies
    5
    Views
    277

    steering knuckle

    noticed that the steering knuckle on the left tire is very sloppy where the ball on the lower control arm pops in. is there a way to tighten that up? looks like there is an adjustment on the ball...
  12. Replies
    16
    Views
    582

    think i may have licked it. started thinking...

    think i may have licked it. started thinking about how the fuel was moving through the line very slowly. this morning i tried to prime by blocking the exhaust dump briefly to see if the fuel would...
  13. Replies
    16
    Views
    582

    thanks for all the help and support. i checked...

    thanks for all the help and support. i checked the head bolt last night. only one took about a 1/4 turn to tighten it up. im gonna go ahead and pull it and check the back plate and head gasket, crank...
  14. Replies
    10
    Views
    298

    build a foam pit with a huge launch ramp in front...

    build a foam pit with a huge launch ramp in front of it. the cars will survive but you can get some seriously huge air. high jump competition or even backflip comp.
  15. Thread: batteries?

    by slo-n-lo
    Replies
    4
    Views
    154

    that is exactly what im looking for. thanks alot....

    that is exactly what im looking for. thanks alot. ill do some searching on the remote recharge set up. thanks alot!!:D
  16. Replies
    16
    Views
    582

    never thought about looping the fuel line.. good...

    never thought about looping the fuel line.. good advice. i do have a Snap-on temp gun in my shop. when i was checking it the other day it was usually around 265-275. a few runs hit 315. so i shut it...
  17. Replies
    10
    Views
    298

    how about a tractor/truck pull. or some skate...

    how about a tractor/truck pull. or some skate ramps to kill the cars on.:lol:
  18. Thread: batteries?

    by slo-n-lo
    Replies
    4
    Views
    154

    batteries?

    the rechargeable servo nimh pack. i was told by my LHS that the MAXX came with the pack in it. it didnt, but i plan on getting one. does it fit into the battery box on the MAXX? does any one make a...
  19. Replies
    16
    Views
    582

    ill see what i can flush out. thanks for the...

    ill see what i can flush out. thanks for the support guys!
  20. Thread: wheelys

    by slo-n-lo
    Replies
    20
    Views
    475

    i have an older .15 rustler. it would wheelie all...

    i have an older .15 rustler. it would wheelie all the time if i were in the grass. occasionally on the track it would get a few small wheelies when i would hammer it out of a corner into the...
  21. Replies
    16
    Views
    582

    i know its getting hot. after the retainig tangs...

    i know its getting hot. after the retainig tangs on the head slider (plastic ring) melted and it flew off. i tried the water drop on the head the water pretty much bounced off the top of the cooling...
  22. Replies
    16
    Views
    582

    i need the nitro guru!

    i cant get this little 2.5r to tune out right. one miniute it runs great. seems that its all dailed in good. then suddenly after a few more high speed runs it hesitates on accel and wont hit second...
  23. Replies
    1,177
    Views
    751,272

    Sticky: still stock. but only had it a week!!...

    still stock. but only had it a week!!
    http://i23.photobucket.com/albums/b377/supermoto150/Picture005.jpg
    http://i23.photobucket.com/albums/b377/supermoto150/Picture006.jpg...
  24. Replies
    22
    Views
    505

    neighbors!!??? ill shoot at my kids!! :D

    neighbors!!??? ill shoot at my kids!! :D
  25. Replies
    22
    Views
    505

    firing mechanism for a roof mounted mini potato...

    firing mechanism for a roof mounted mini potato gun :lol:
Results 1 to 25 of 40
Page 1 of 2 1 2