Search:

Type: Posts; User: CrazyXMAXX

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. alignment issue fix amplified wear/damage by...

    alignment issue fix

    amplified wear/damage by using aluminum A-arms...
  2. damage looks to be from using aluminum lower...

    damage looks to be from using aluminum lower A-arms
    non flexible arms transfers stress to the rear diff housing,etc
    rear 6s diff gears/ trans gear failed -
    new rear diff cover and full set of...
  3. Replies
    454
    Views
    86,464

    it's been 5 months without repairing the udr's ...

    it's been 5 months without repairing the udr's
    1 of my least favorite rc's to work on , an drive
    udr's wear out parts ,maintenance needed - quicker than any other

    run something
  4. Replies
    3
    Views
    216

    not satisfied ? take a video - send to traxxas...

    not satisfied ?
    take a video - send to traxxas support
    30 day warranty ends soon
  5. Replies
    1,620
    Views
    260,575

    have installed atomic aluminum steering servo...

    have installed atomic aluminum steering servo saver assembly on 2 Xmaxx so far
    the stock plastic servo savers haven't lasted 6 months on my Xmaxx's once a week runs
    all the assemblies bearings were...
  6. Replies
    5
    Views
    275

    $300 - $600 rusty screws are useable - wd them...

    $300 - $600
    rusty screws are useable -
    wd them , rub with an old tooth brush
    output yoke wear will show proof of use
    steering servo saver slop -
  7. Replies
    75
    Views
    12,138

    kevin Talbot specials ...

    kevin Talbot specials
    ...
  8. ah ha not LVC - TSD thermal shutdown 30/35...

    ah ha not LVC - TSD thermal shutdown

    30/35 might be fast for 1 short run - not suggested
  9. stock motor - 20/46 gears is bout as high you can...

    stock motor - 20/46 gears is bout as high you can go without hitting LVC
  10. have ran 2 vxl8s esc's since the 8s power up...

    have ran 2 vxl8s esc's since the 8s power up system became available
    first new 8s roller from jennys rc was $475 - no body or esc -both vxl8s are still operating
    max6 punch is worth the change
    ...
  11. Replies
    1,620
    Views
    260,575

    front cvd pin failed on #1 xmaxx with a max6 +...

    front cvd pin failed on #1 xmaxx with a max6 + hostile 5b MX tires - 6s from 2016
    rear axle failed at the ball, on #2 xmaxx with a max6 and stock 8s tires - $300 ebay 6s xmaxx
    the 8s xmaxx ,stock...
  12. no even running 34/47 gears has never hit TSD

    no
    even running 34/47 gears
    has never hit TSD
  13. Replies
    10
    Views
    2,661

    stock 8s can run 20/46 without hitting tsd

    stock 8s can run 20/46 without hitting tsd
  14. Replies
    16
    Views
    405

    Xmaxx #3 has needed it's servo wire replugged in...

    Xmaxx #3 has needed it's servo wire replugged in 3 times now
    put a very little e6000 on the connector/wires/receiver this time
    have been using stock plastic servo gears for over 3 years - rarely...
  15. Replies
    16
    Views
    405

    have you ; removed the servo linkage screw ,on...

    have you ;
    removed the servo linkage screw ,on the servo saver
    then check steering moves freely
    then check servo - may need plugged back in
    what noise does it make
    step by step
  16. Replies
    1
    Views
    282

    on the app :channel setup brake & throttle up...

    on the app
    :channel setup
    brake & throttle up to 120%
    :driver effects
    throttle sensitivity 0-100
    braking 0% - 100%
    20/46 gears for speed
  17. Replies
    2
    Views
    443

    call traxxas support for defective esc...

    call traxxas support for defective esc replacement warranty

    or replace with a hobbywing max6
  18. Thread: Motor

    by CrazyXMAXX
    Replies
    12
    Views
    765

    when rpm's run out with the 1200kv motor - the...

    when rpm's run out with the 1200kv motor -
    the 1600kv still has torque , and rpm's to pull
    have to agree with numbers - smile gets bigger with 1600 motor
    kevin talbot runs max6 an 1600kv

    do...
  19. Thread: Motor

    by CrazyXMAXX
    Replies
    12
    Views
    765

    Have been running the 1600kv motor on 8s since...

    Have been running the 1600kv motor on 8s
    since the power up kit / 8s came out
    the 1600kv motor is faster and has more torque
    than the 1200kv motor-on my original 6s,
    max6, 25/46 with hostile...
  20. Replies
    454
    Views
    86,464

    thrashing the udr's over a year now replaced the...

    thrashing the udr's over a year now
    replaced the steering servo saver again on #2- 2nd or 3rd time now
    going to order aluminum servo saver next time
    they don't break just wear out= sloppy...
  21. tape or plug the holes in the rims, before dirt...

    tape or plug the holes in the rims, before dirt gets in
    or melt holes in the tires
    consider installing the open diff and 34 47 gearing
    40wF 70wR shock fluid with 8-10mm of lowering spacers
    green...
  22. Replies
    3
    Views
    414

    Xmaxx light kit

    https://www.youtube.com/watch?v=Y2IzdyDySjs
  23. Replies
    4
    Views
    362

    using a 20t pinion with the 46t spur- with the...

    using a 20t pinion with the 46t spur-
    with the pin mesh system works fine
    stock 46t spur still working here after 2 years
    call traxxas support ,
    they will send you a replacement 46t spur gear
  24. Replies
    454
    Views
    86,464

    direct short = melted wires test positive /...

    direct short = melted wires

    test positive / negative with multi tester
  25. Replies
    6
    Views
    804

    8s gears rarely fail...

    8s gears rarely fail
    https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2380057.m570.l1313.TR10.TRC2.A0.H0.Xtra7790.TRS2&_nkw=tra7790&_sacat=0...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4