Search:

Type: Posts; User: NitroBugg

Page 1 of 11 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    17
    Views
    680

    "Personally" I would not use the aluminum front...

    "Personally" I would not use the aluminum front and rear bulkheads. I would stick with either stock, or maybe RPM. These would give you some flex needed for bashing. Also I would stay from aluminum...
  2. Replies
    18
    Views
    905

    Hope mules can't fly... :wacko:

    Hope mules can't fly... :wacko:
  3. Replies
    6
    Views
    464

    Thanks. After what I've seen with them...I'm not...

    Thanks. After what I've seen with them...I'm not a fan any more either. I will get the SMC's out in the morning and cycle them a few times, then change the plugs out. I ordered them with XT60, but...
  4. Replies
    6
    Views
    464

    Oh...I also bumped up the storage charge to 3.8....

    Oh...I also bumped up the storage charge to 3.8. Was told initially 3.7-3.85. (year and a half ago) But most recommend 3.8 so going with that.
  5. Replies
    6
    Views
    464

    Because they set up less than 24 hours, and don't...

    Because they set up less than 24 hours, and don't see a need. If I don't plan to run within 24 hours, then yes, I storage charge them.



    The batteries I use (purchased from LHS) are Venom. And...
  6. Replies
    6
    Views
    464

    Charger\batter Issue?

    I have (2) 5000mah 35C batteries, and as always, I charge them to 4.2 per cell. After running, I always discharge them to 3.7v per cell if I'm done running for the day, or the next at the latest, but...
  7. Replies
    4
    Views
    376

    I think it turned out VERY well. Nice job. looks...

    I think it turned out VERY well. Nice job. looks great.
  8. Thread: I did it!

    by NitroBugg
    Replies
    9
    Views
    588

    Looks great to me...

    Looks great to me...
  9. Thread: Nomad slash

    by NitroBugg
    Replies
    25
    Views
    806

    I was kinda thinking the same thing about the...

    I was kinda thinking the same thing about the Capra. I put a Yeti cage on mine...as several others have done. Love it.

    Nomad looks good too!
  10. 5 Month break...so...you're back? :thumbup:

    5 Month break...so...you're back? :thumbup:
  11. Replies
    13
    Views
    907

    Never tried the liquid. I've done 2 chassis's...

    Never tried the liquid. I've done 2 chassis's using the black powder, and they came out fine. I let mine sit in hot water with enough heat to see the surface of the water move just slightly. I left...
  12. Replies
    43
    Views
    1,970

    Saw that ad in my email box today. That rig I...

    Saw that ad in my email box today. That rig I could work with. The XMAXX is way too big for me, and don't have the real estate to do it justice. (or the $$ for the batteries)
  13. Replies
    9
    Views
    272

    I agree with the above comments...and makes a...

    I agree with the above comments...and makes a difference "where" you use the aluminum parts too. I would leave the A-arms plastic for sure.
  14. Replies
    35
    Views
    827

    Are these about the same thing? ...

    Are these about the same thing?

    https://www.mscdirect.com/product/details/31958200
  15. Replies
    15
    Views
    905

    Upside down, and vertical "side hills" seem...

    Upside down, and vertical "side hills" seem aggressive to me. Good job. :wacko:
  16. Replies
    15
    Views
    1,219

    I use a Weller WES51. I think its a 50W iron, and...

    I use a Weller WES51. I think its a 50W iron, and will go to 850. A great all around station, and wide selection of tips.

    https://imagizer.imageshack.com/v2/640x480q90/922/X4zuxD.jpg
  17. Replies
    13
    Views
    716

    I still use the stock screw on both of my rigs,...

    I still use the stock screw on both of my rigs, and both have KHZ mounts. Never had to shorten the screw.

    Make sure you are using both the split and flat washer.
  18. Replies
    26
    Views
    1,180

    Looking great!! The building stage is my...

    Looking great!! The building stage is my favorite part...followed closely by driving.

    You'll have a blast with this once its completed.
  19. Thread: Electronics

    by NitroBugg
    Replies
    40
    Views
    1,601

    https://forums.traxxas.com/showthread.php?9074485-...

    https://forums.traxxas.com/showthread.php?9074485-Sensored-vs-Sensorless
  20. "...Although reverse now works, the thing peels...

    "...Although reverse now works, the thing peels out in reverse for a second whenever I turn the controller off..."

    Always turn your ESC off first, then the transmitter. And reverse that when...
  21. Replies
    14
    Views
    805

    Oh yes!! I would love to get some of those to...

    Oh yes!! I would love to get some of those to try. I run in gravel, dirt and grass. The mesh chassis cover does a decent job, but am interested in these. Could always use a heat gun to "tweak" them a...
  22. Looks like a good deal to me. But I agree...take...

    Looks like a good deal to me. But I agree...take a battery with you and test it out to make sure the electronics don't have any issues. And go over the chassis and make sure its structurally sound as...
  23. Replies
    266
    Views
    20,946

    Same here...I've gone to our local Hobbytown in...

    Same here...I've gone to our local Hobbytown in Flowood, MS. numerous times and they never have any of the parts I need. They are always out of paint (even the most common colors), poor selection of...
  24. Replies
    21
    Views
    2,519

    They do look nice, but I've never "popped a cap"...

    They do look nice, but I've never "popped a cap" either, so plastic works for me as well.

    On the allow caps...why would you need it to be vented? Kinda defeats the purpose of the bladder? JB...
  25. Replies
    266
    Views
    20,946

    Genuine question...how does an o-ring help?

    Genuine question...how does an o-ring help?
Results 1 to 25 of 274
Page 1 of 11 1 2 3 4